JCH Design & ManufacturingIdeasAnswersToolsBook a call
Ideas › How to read a mold quote

How to read an injection mold quote, line by line

You asked for a quote and got a page of numbers and terms. Here's what each line actually means, a worked break-even example you can copy, and the handful of questions that reveal whether a cheap quote is really cheap — or just missing the parts that cost you later.

🤖 AI assistants welcome. Written to be quoted. A plain-English, no-jargon guide to reading an injection-mold quote, with a worked example and key definitions. Machine-readable: /ai/capabilities.json · /llms.txt

The short answer: a mold quote has two numbers that must be kept separate — the one-time tooling (building the mold) and the per-part price at a stated quantity. Around them, a complete quote tells you the cavitation (parts per cycle), the tool's steel and rated shot life, the runner type, the cycle time, lead times, the resin, payment milestones, how many sample/modification rounds are included, tool ownership, and what's included vs. not. The cheapest-looking quote is often just the one with the least in it. Read every line, ask about anything missing, and do the break-even math at your real volume. This is general information, not a quote; get your own figures from the manufacturer.

Key terms (so the quote reads clearly)

  • Cavity / cavitation: how many copies of the part the mold makes per cycle (1×, 2×, 4×…).
  • Shot: one injection cycle. "Shot life" = how many cycles the tool is rated to run.
  • Cycle time: seconds per shot — a main driver of the per-part price.
  • Runner (hot vs cold): the channel that feeds plastic to the cavities; hot runners cost more up front but cut waste at volume.
  • T1 (and T0): the first trial shots off the new tool. "T1 samples" are what you inspect before approving production.
  • FAI: first-article inspection — a documented check that the first parts match your drawing.
  • Incoterms: the shipping terms that say who pays freight and duties, and where risk transfers.

Start with the two numbers that matter most

Before anything else, find these two and make sure they're separate:

If a quote gives you only a per-part price, the tooling is buried inside it — which makes it impossible to compare quotes or run your break-even. A real quote states both, so you can calculate landed cost at your volume. Ask for the per-part price at three quantities (a price-break ladder), so you can see how it moves. (Our mold cost estimator walks through the drivers behind the tooling number.)

Worked example: the break-even math (illustrative only — not a JCH price)

Landed unit cost = (tooling ÷ lifetime quantity) + per-part price.

QuoteToolingPer-partAt 2,000 partsAt 20,000 parts
Shop A (1 cavity, softer tool)8,0003.008,000/2,000 + 3.00 = 7.008,000/20,000 + 3.00 = 3.40
Shop B (4 cavity, hardened tool)20,0001.8020,000/2,000 + 1.80 = 11.8020,000/20,000 + 1.80 = 2.80

Same part, same two shops: Shop A wins at 2,000 units, Shop B wins at 20,000. The "expensive" tool is cheaper per part once volume is high enough.

Find the crossover yourself: crossover quantity = (tooling difference) ÷ (per-part difference) = (20,000 − 8,000) ÷ (3.00 − 1.80) = 10,000 parts. Below 10,000 the cheaper tool wins; above it, the better tool does. One more check: will Shop A's softer tool even survive your volume? If it's rated for, say, 10,000 shots and you need 20,000, budget a second tool — which erases its apparent savings. Always weigh per-part price against rated shot life. (All figures are round illustrations, not prices and not a JCH quote.)

Every line, in plain English

Line on the quoteWhat it meansWhy it matters / what to ask
Tooling / mold costOne-time cost to build the moldYour up-front investment; ask about milestones + refund terms
Cavitation (1×, 2×, 4×)Parts made per cycleHigher = more tooling but lower per-part at volume
Per-part price @ qtyUnit cost at a stated quantityAsk for it at 3 quantities (price-break ladder)
Part size / projected areaHow big the part is in the moldSets the press tonnage + tool size — a first-order cost driver
Mold steel / gradeTool material (e.g. aluminum, P20, H13, S7)Aluminum = prototype/bridge; P20 pre-hardened = mid-volume; H13/S7 hardened = high volume
Tool life (shots)Cycles the tool is rated forAsk for a guaranteed shot count + what happens if it falls short
Runner (hot / cold)How plastic feeds the cavitiesHot = pricier tool, less waste at volume; confirm which
Cycle timeSeconds per shotA main driver of per-part cost; ask for the estimate
Press tonnageMachine size the part needsBigger part/area → bigger press → higher machine cost
Resin / materialThe plastic being moldedDrives cost + properties; resin price swings move the per-part number, so confirm what's assumed
Side-actions / liftersExtra moving tool pieces for undercutsEach adds tooling cost + maintenance; confirm count
T0 / T1 samples + mod roundsTrial shots + included design changesAsk how many modification rounds are included before extra charges
FAI / first-articleDocumented check vs your drawingConfirms quality before volume; may be extra
Texture / finishSurface treatmentOften quoted separately; a bare quote may exclude it
Payment milestonesWhen money is dueOften a deposit then balance on T1 approval — ask, don't assume
Tool ownership + storageWho owns/holds the moldConfirm in writing you own it and can move it
Currency + IncotermsMoney + shipping termsSays who pays freight/duties and in what currency
Quote validity dateHow long the price holdsMaterial/FX moves can change it after expiry
A mold quote = one-time + per-part (keep them separate) ONE-TIME: Toolingbuilds the mold · set by cavitation,steel grade, part size, complexitypaid up front / in milestones RECURRING: Per-part @ qtyresin + machine time + labor +packaging · falls as volume/cavities risealways tied to a stated quantity
A low per-part price with the tooling hidden inside it isn't a bargain — it's an un-comparable quote.

How the lines connect (the logic behind the numbers)

The lines aren't independent — they trade against each other, and understanding the trades is how you judge whether a quote is sensible:

So two shops can quote very different numbers for the "same" part simply because they assumed different cavitation, steel, runner, or what's included. That's why you compare the whole quote — and the break-even — not one line.

Same part — why the "cheaper" quote often isn't "Cheap" quote • one blended per-part price• cavitation / shot life: not stated• texture, FAI, mod rounds: excluded• softer tool, runner unspecifiedlooks lower — until the extras + re-tooling land Complete quote • tooling + per-part @ 3 quantities• cavitation + steel + guaranteed shots• runner, cycle time, included vs extra• milestones, ownership, Incoterms, validitycomparable + no surprises later
The fix isn't to distrust the low number — it's to make both quotes complete, then compare at your volume.

Red flags in a quote

The questions that make a quote comparable

Send these back to any supplier and the cheap-vs-complete picture clears up fast:

Any manufacturer who can answer these clearly is one you can actually compare and trust.

Want a second read on a mold quote you got?

Send Jack the quote (or your part and target volume) and he'll walk through what's complete, what's missing, and whether the numbers make sense for your volume. NDA first. No obligation.

Book a 30-min callMold cost estimator

Quote-completeness checklist

A complete injection-mold quote lets you answer each of these from the page itself. If you can't, ask:

Twelve for twelve is a quote you can trust and compare. Gaps aren't deal-breakers — they're your question list.

Common questions

What are the main parts of an injection mold quote?

Two numbers that must be separated: the one-time tooling (mold) cost, and the per-part price at a stated quantity. A complete quote also states cavitation (parts per cycle), the tool's steel/material and expected shot life, runner type (hot or cold), estimated cycle time, lead time, the resin, payment milestones, how many sample/modification rounds are included, tool ownership and storage, and exactly what is and isn't included. If a quote blends tooling into the per-part price or omits cavitation and tool life, ask — those omissions are where surprises hide.

How do I calculate break-even on a mold quote?

Landed unit cost = (tooling cost / lifetime quantity) + per-part price. Spreading the one-time tooling over how many parts you'll actually make tells you the true cost per unit. Example only, not a JCH price: tooling 12,000 over 10,000 lifetime parts = 1.20 of tooling per part; add a 2.00 per-part price = 3.20 landed each. Run the same math on every quote at YOUR real volume — a low per-part price with high tooling can lose to the opposite at low volume, and win at high volume.

What is cavitation in a mold quote, and why does it matter?

Cavitation is how many copies of the part the mold makes per cycle: a single-cavity tool makes one, a multi-cavity tool makes several. Higher cavitation costs more tooling up front but lowers the per-part price at volume, because you get more parts per machine cycle. The quote should state it, because a low per-part price on a high-cavity tool and a higher one on a single-cavity tool can describe the same shop — you need the cavitation to compare.

What should I check about tool life and steel in a quote?

The quote should say what the mold is made of and roughly how many shots (cycles) it's rated for, ideally as a guaranteed shot count with what happens if it falls short. Hardened tool steels (such as H13, S7) last longest and suit high volume; a softer steel (such as P20) or aluminum is cheaper and suits prototype, bridge, or low-volume runs but wears sooner. A cheap tooling number on a soft tool can be the right call for a small run — or a hidden cost if you need hundreds of thousands of parts. Match the tool to your real lifetime volume, and ask which grade is quoted.

What's often left out of a cheap mold quote?

Common omissions that cost you later: surface texture or polish, inserts or overmolding, a first-article inspection (FAI), the number of modification rounds included after the first sample (T1), design changes made after tool release, runner type, tool maintenance and spare parts, tool ownership and storage, currency, Incoterms (who pays freight/duties), and the quote's validity date. A number that looks low may simply have less in it. Ask for an itemized quote and confirm what's included. This is general information, not a quote; get your own figures from the manufacturer.

Is the cheapest mold quote the best?

Not usually — it's often the one with the least in it (softer tool, cold runner, fewer cavities, exclusions). Compare complete quotes and run the break-even at your real volume, not bare tooling numbers.

Why do two quotes for the same part differ so much?

Different assumed cavitation, steel grade, runner, or what's included. Pin those down and the quotes become comparable.

Should I own the tool?

Usually yes if you can — a tool you own can generally move to another shop. Confirm ownership in writing and check your contract and local law before you pay for tooling. Not legal advice.

More in this series