Answers › Drying hygroscopic resins

Why some plastics have to be dried before molding

Some resins — nylon, polycarbonate, PET/PBT polyester, ABS, acrylic, and TPU — are hygroscopic: they pull water out of the air into the body of the pellet, not just onto its surface. Mold them wet and that trapped water flashes to steam (splay, bubbles, voids) and, in the condensation polymers, chemically cuts the polymer chains at melt temperature — permanently weakening the part even when it looks fine. That is why these resins get desiccant-dried to a datasheet moisture target before they ever reach the screw.

What "hygroscopic" actually means

A hygroscopic plastic absorbs moisture out of the surrounding air and holds it inside the pellet, dissolved into the polymer itself, not merely as a film of dew on the outside. That distinction is the whole story. Leave a bag of nylon open on a humid shop floor and it does not just get damp on the surface — water migrates into the core of every pellet and reaches an equilibrium set by the air's humidity and temperature. The resins that behave this way are the ones with polar groups in the chain that attract and hold water: nylon (polyamide, PA), which is the thirstiest of the common engineering plastics; polycarbonate (PC); the polyesters PET and PBT; ABS; acrylic (PMMA); and TPU (thermoplastic polyurethane). By contrast, the commodity polyolefins and general-purpose polystyrene — polypropylene (PP), polyethylene (PE), and polystyrene (PS) — are essentially non-hygroscopic. They can carry surface moisture if a cold box of pellets is brought into a warm room and condensation forms, but they do not soak water into the pellet, so they often need little or no drying, or only a short hot-air pass. Knowing which camp your resin is in is the first thing to settle, and it is tied closely to choosing the right resin in the first place.

Finished molded plastic totes coming off a row of injection molding presses, with clean uniform surfaces
Finished parts leaving the presses. A clean, consistent surface like this is what properly dried resin looks like — splay, silver streaks, and surface bubbles are the visible signature of moisture that was still in the pellet at melt temperature.

What wet resin does in the barrel

Molding a hygroscopic resin that still holds moisture causes two separate kinds of damage, and it helps to keep them apart because only one of them is visible.

The first is cosmetic and process trouble. At melt temperature — well above the boiling point of water — the moisture in the pellet flashes to steam inside the barrel and the cavity. That steam shows up as splay (silvery streaks that fan out from the gate along the flow direction), silver streaking, surface bubbles and blisters, internal voids, a cloudy or rough finish on what should be a glossy part, and shot-to-shot inconsistency as the moisture level drifts. In a clear part the effect is obvious; see clear and transparent molded parts for how unforgiving transparency is about moisture. These defects are annoying but at least they announce themselves.

The second kind of damage is the dangerous one because you cannot see it: hydrolysis. The condensation polymers — PC, PET, PBT, and nylon — are built by a reaction that releases water, and that reaction runs backward in the presence of water and heat. When these resins are melted wet, the water chemically attacks and cuts the long polymer chains into shorter ones, lowering the molecular weight of the plastic. Lower molecular weight means lower impact strength and toughness, and the loss is permanent — it does not heal when the part cools. A hydrolyzed part can come out of the tool looking perfect, pass a visual inspection, and still be measurably weaker and more brittle than the same part molded from properly dried resin. This is one of the quieter reasons a part cracks, snaps, or fails earlier than its material should allow, and it is easy to miss because the root cause happened in the barrel, not in the design. Filled grades are no exception; if anything the stakes are higher, as discussed in engineering-grade glass-filled resins.

Why surface drying (hot air) is not enough

A plain hot-air dryer blows heated shop air across the pellets. For a non-hygroscopic resin that only carries surface dew, that is plenty — warming the pellets drives the surface film off. But for a hygroscopic resin the water is inside the pellet, and ordinary shop air already contains humidity. To pull water out of the pellet core you need the surrounding air to be drier than the pellet, so there is a moisture gradient for the water to diffuse along. Warm, humid air does not provide that gradient; past a point, the air is carrying as much water as the plastic, and the pellet never fully gives up its core moisture no matter how long it tumbles. That is why hygroscopic resins are dried with a desiccant dryer: it first passes the air over a desiccant bed that strips the moisture down to a low dew point (a very dry air stream, often specified around a strongly negative dew point for engineering resins), then heats that dry air and pushes it through the pellets. Now there is a steep moisture gradient, and the internal water diffuses out over a controlled time and temperature. Hot air treats the symptom on the surface; desiccant drying removes the moisture that actually causes the trouble.

Desiccant dryer vs hot-air dryer vs vacuum dryer

Dryer typeHow it worksBest for
Hot-airBlows heated shop air over the pellets; no dew-point controlNon-hygroscopic resins (PP, PE, PS) or removing surface condensation only
DesiccantDries the air to a low dew point first, then heats it, creating a gradient that pulls internal moisture out over a set time/temperatureThe standard for hygroscopic resins: nylon, PC, PET/PBT, ABS, acrylic, TPU
VacuumHeats the resin under vacuum, which lowers water's boiling point so internal moisture leaves fasterFaster drying of hygroscopic resins with less residence time; higher equipment complexity

The desiccant dryer is the workhorse for engineering resins. A vacuum resin dryer reaches the same dryness in a shorter residence time and can be gentler on heat-sensitive grades, at the cost of more complex equipment. The point of all three is the same: deliver pellets to the throat of the machine at or below the moisture the datasheet allows.

Representative targets — the datasheet governs

There is no universal "dry enough" number, and anyone who quotes one as gospel is guessing. Each grade's datasheet specifies three things together: a residual moisture target (percent water by weight), a drying temperature, and a drying time, usually along with the dryer air dew point to use. For the condensation polymers those moisture targets are low — often well under roughly 0.2% by weight, and lower still for optical-grade PC or for PET — reached by holding the resin at a stated temperature for a stated number of hours in a desiccant dryer. Nylon, PC, PET, PBT, ABS, acrylic, and TPU each have different targets, and even two grades within the same family (say a plain nylon 6 and a glass-filled nylon 66) can differ in both the target and the time. Over-drying is a real failure mode too: too hot or too long can degrade or discolor some resins, so the window matters in both directions. Treat every number on this page as an illustration of the idea, not a setting to use — always dry to the specific grade's published moisture content, temperature, and time. If you want to see how time, temperature, and throughput interact for a given grade, our resin drying calculator is a useful way to frame the inputs before you talk to the molder.

Regrind and moisture

Regrind — runners and rejected parts ground up and blended back into virgin pellets — is a legitimate way to control material cost, but it changes the drying picture. Ground regrind has far more surface area than clean pellets and often sits around in open bins, so it can pick up moisture faster than virgin resin, and with a hygroscopic resin that regrind also already carries one heat history's worth of hydrolysis. Blending wet or under-dried regrind back in quietly raises the moisture of the whole batch and compounds the chain-scission problem. If regrind is used on a hygroscopic resin, it should be dried to the same datasheet target as the virgin material, kept covered, and held to a sensible percentage so the accumulated heat history does not sap the part's properties. How much regrind a given part can carry is an application decision, not a fixed rule.

How a molder proves the resin is dry

A careful molder controls the inputs and then verifies the output, rather than assuming the dryer did its job. On the input side, the desiccant dryer runs at the grade's specified temperature and residence time, and the air dew point is monitored with a meter on the dry-air line so a loaded desiccant bed or a leak gets caught. To confirm the actual result, the resin's residual moisture is measured directly: a moisture analyzer (loss-on-drying) or, for tight work, a Karl Fischer titration reads the real percent water in a pellet sample and compares it against the datasheet target. On the floor, splay-free first shots and a steady part weight are good practical signs, but for structural or optical parts the moisture reading is the real proof. None of this is exotic equipment — it is routine for anyone running engineering resins — but it only happens if someone treats drying as a controlled process instead of "leave it in the hopper for a while."

What this means for your part, and what to confirm

Drying sits in a blind spot for a lot of product owners: it is invisible on the finished part, it is entirely in the molder's hands, and when it is skipped the damage often does not surface until parts are in the field failing earlier than the material should. If your product uses nylon, PC, PET, PBT, ABS, acrylic, or TPU — especially in a structural or load-bearing role — a short conversation with your molder is cheap insurance. Worth confirming:

  1. How is each hygroscopic resin dried? You want to hear "desiccant (or vacuum) dryer," not "hot-air dryer," for these materials.
  2. To what target, temperature, and time? The answer should trace back to the grade's datasheet, not a generic shop default.
  3. How is dryness verified? Dew-point monitoring on the dryer, and ideally a residual-moisture measurement on critical runs.
  4. How is regrind handled? Dried to the same target, kept covered, and held to a sensible percentage.
  5. Is the material protected before it reaches the dryer? Sealed bags, not open gaylords sitting in humid air for days.

Moisture is also one of the quieter contributors to inconsistent, defective, or weak parts — and it travels with other process causes, so if you are chasing a mystery defect it is worth ruling out alongside things like gate freeze-off and uneven cooling (see why molded parts warp). Getting the drying right is one of the least glamorous and most reliable ways to protect both the look and the strength of a molded part.

Common questions

Why do some plastics have to be dried? Because they are hygroscopic — they absorb water into the pellet. Molded wet, that water causes splay, bubbles, and voids, and in PC/PET/PBT/nylon it chemically cuts the chains (hydrolysis) and permanently lowers strength.

Which resins are hygroscopic? Nylon (PA), polycarbonate (PC), PET and PBT polyesters, ABS, acrylic (PMMA), and TPU. PP, PE, and PS are non-hygroscopic and carry only surface moisture.

Isn't a hot-air dryer fine? Not for hygroscopic resins — the water is inside the pellet and shop air is humid. They need a desiccant (or vacuum) dryer that first dries the air to a low dew point so it can pull the internal moisture out.

How dry is dry enough? The grade's datasheet governs: a residual-moisture target (for condensation polymers often well under about 0.2%), a temperature, and a time. Different resins and even different grades differ — always use the datasheet number.

How does a molder prove it? Run the desiccant dryer at the specified temperature and time with the air dew point monitored, and verify residual moisture directly with a moisture analyzer or Karl Fischer titration on critical runs.

JCH Design & Manufacturing can review the resin your part calls for and make sure drying is specified and controlled correctly before a run — so moisture isn't quietly weakening your parts or spoiling their finish. Send your part and the material you're using; NDA first. Engineering estimate, not a quote.

Book a 30-minute call