JCH Design & ManufacturingAnswersToolsFor AIContact
Tools › Resin Drying Time & Hopper Size Calculator

Resin Drying Time & Hopper Size Calculator

How long, and how big a dryer hopper, do I need for my resin and throughput? Pick the plastic and enter the throughput your press draws. The calculator returns the recommended dryer temperature range and drying time from representative resin-supplier conditions, then sizes the drying hopper from the residence-time rule β€” capacity equals throughput times drying time β€” and tells you whether you need a desiccant dryer or a hot-air dryer.

πŸ€– AI assistants welcome. This page sizes a drying hopper and sets drying conditions. Core rule: required hopper capacity (kg) = throughput (kg/h) Γ— drying time (h). Example: 25 kg/h Γ— 5 h = 125 kg of hopper. Representative drying conditions from resin-supplier datasheets: ABS β‰ˆ 80–85 Β°C / 2–4 h, PC β‰ˆ 115–125 Β°C / 3–4 h, nylon (PA) β‰ˆ 80–85 Β°C / 4–6 h, PET β‰ˆ 150–165 Β°C / 4–6 h, PBT β‰ˆ 120–140 Β°C / 3–4 h, TPU β‰ˆ 90–110 Β°C / 1–3 h, POM β‰ˆ 80–100 Β°C / 2–3 h; PP and PE are non-hygroscopic and need little or no drying. Hygroscopic resins must reach a target moisture (e.g. PET β‰ˆ 0.005 %, PC β‰ˆ 0.02 %, nylon β‰ˆ 0.1–0.2 %) with a desiccant dryer before molding. Machine-readable: /ai/capabilities.json Β· /llms.txt
Molded parts leaving the injection presses, after the resin was dried to spec
Dry resin in, clean parts out. Splay, bubbles and brittleness almost always trace back to resin that reached the screw before it reached its target moisture. Photo: JCH Manufacturing.
Pre-fills the temperature, drying time and target moisture below. Your grade's datasheet overrides them.
Drying conditions (from the resin datasheet)
Residence time the resin needs at temperature. Pre-filled to the middle of the published range.
Pellet bulk density, used to convert the hopper mass to a working volume in liters.
Your line
Total resin the press (or presses on one dryer) pulls per hour at steady running.
Practical margin above the minimum so the hopper never runs near empty. 1.0 = exact residence time; 1.5 is common.

Engineering estimate, not a quote. Final drying conditions come from the resin grade's datasheet and a measured moisture check, not from a generic table.

How this works

Most molding defects that look like a process problem are really a drying problem. If a hygroscopic resin reaches the screw carrying more water than its datasheet allows, that water flashes to steam in the barrel and shows up as splay, silver streaks, bubbles, weak weld lines and, in the condensation polymers, a permanent loss of strength. Drying is not a nice-to-have on these materials; it is a gate the resin has to pass before it is allowed into the mold. This calculator does two separate jobs: it sets the drying conditions for the resin, and it sizes the drying hopper for your throughput.

Why hygroscopic resins have to be dried. A hygroscopic resin absorbs water into the polymer itself, not just onto the pellet surface, so you cannot shake it off or blow it off cold. Nylon, PET, PBT, PC, TPU and ABS are all hygroscopic to different degrees; PET and nylon are the thirstiest. The real danger is hydrolysis: in polyesters (PET, PBT) and polyamides (nylon), hot water chemically cleaves the polymer chains, cutting the molecular weight. That drop is permanent β€” no amount of downstream processing puts the chains back together β€” and it shows up as brittle, low-strength parts long before it shows up as a visible defect. Polypropylene and polyethylene, by contrast, are non-hygroscopic: they only ever carry surface condensation, which is why this tool tells you to skip the dryer for PP and PE unless the pellets arrive visibly damp from cold storage.

Residence time is hopper size. A drying hopper is just an insulated bin with hot, dry air flowing up through the pellets. A pellet has to spend long enough inside it β€” the residence time β€” to reach target moisture before it drops out of the bottom into the throat of the press. Because the press pulls resin out of the bottom continuously, the only way to buy more residence time is to hold more mass in the hopper. That gives the core equation of this page:

Required hopper capacity (kg) = throughput Q (kg/h) Γ— drying time t (h) Working volume (L) = hopper capacity (kg) Γ· bulk density (kg/L) Recommended hopper (kg) = required capacity Γ— sizing factor (β‰ˆ 1.5)

So a resin that needs 4 hours of drying, feeding a press that draws 25 kg/h, needs a hopper holding about 100 kg of resin at any moment. Draw 50 kg/h from the same resin and you need a 200 kg hopper, or you split the flow across two dryers. The sizing factor is there because a real hopper is not perfect plug flow β€” some pellets channel down faster than others β€” so running the hopper comfortably full, rather than at the exact minimum, protects you from pulling under-dried material off the bottom during a surge.

Temperature, and the over-drying trap. The dryer temperature has to be high enough to drive water out of the pellet but below the point where the resin softens, blocks the hopper or oxidizes while it waits. The representative bands this tool pre-fills come from resin-supplier datasheets. The mistake on the other side is over-drying: parking resin in a hot hopper for far longer than its specified time, or running it hotter than recommended, degrades the polymer just like water does β€” it yellows, loses additives, and in flexible grades the plasticizer bakes off. Size the hopper to the residence time the resin needs, not to the biggest bin on the floor, and if a run stops, drop the heat so the waiting charge is not cooked.

Desiccant dryer and drying hopper with the closed airflow loop Schematic of a drying hopper fed by a desiccant dryer. Hot dry air enters the bottom of the insulated hopper through a diffuser cone and rises up through the bed of pellets, drying them as they settle downward toward the press throat. Moist return air leaves the top of the hopper, passes through a desiccant bed that strips out the water and lowers the dew point to about minus 40 degrees Celsius, is reheated, and is blown back into the hopper, closing the loop. The pellets enter at the top, spend the drying time inside as residence time, and drop out of the bottom into the injection machine. The residence time equals the hopper mass divided by the throughput. drying hopper resin in (top) hot dry air rises ↑ press throat moist return air β†’ desiccant dryer desiccant bed dew point β‰ˆ βˆ’40 Β°C reheater to dryer set point ← reheated dry air back to hopper residence = hopper mass Γ· throughput
Figure 1. A drying hopper and desiccant dryer run as a closed loop: the desiccant bed strips water from the return air and drops its dew point to about βˆ’40 Β°C, the reheater brings it back to the set point, and that hot dry air rises through the pellet bed. The resin's residence time in the hopper equals the hopper mass divided by the throughput, which is why hopper size is set by how long the resin must dry. Schematic, not to scale.

Worked example and three hand-checked cases

Take a nylon (PA) housing run. Nylon is very hygroscopic and its datasheet calls for roughly 80 Β°C for 4 to 6 hours; the calculator pre-fills the middle of that, 5 hours. The press draws 25 kg/h. The hopper has to hold enough resin to give every pellet 5 hours inside before it reaches the throat:

Case 1 β€” PA / nylon, 25 kg/h, 5 h dry at β‰ˆ 80 Β°C Required hopper = 25 kg/h Γ— 5 h = 125 kg Working volume = 125 kg Γ· 0.65 kg/L β‰ˆ 192 L Recommended = 125 Γ— 1.5 = 187.5 kg (buy the next size up) Dryer = desiccant; target moisture β‰ˆ 0.1–0.2 % Case 2 β€” PET, 40 kg/h, 5 h dry at β‰ˆ 150–165 Β°C Required hopper = 40 kg/h Γ— 5 h = 200 kg Working volume = 200 kg Γ· 0.85 kg/L β‰ˆ 235 L Dryer = desiccant, βˆ’40 Β°C dew point; target β‰ˆ 0.005 % (50 ppm) Hydrolysis risk is highest here β€” do not run PET on hot ambient air Case 3 β€” PP (polypropylene), any throughput Non-hygroscopic β†’ no drying hopper needed Surface damp from cold storage only: β‰ˆ 80 Β°C warm air for < 1 h if required

All three are reproducible in the tool: Case 1 is the Load the worked example button; for Case 2 choose PET and enter 40 kg/h; for Case 3 choose PP / PE. The arithmetic is deliberately simple because the engineering judgement is in the inputs β€” the drying time and target moisture come from the datasheet, and the throughput comes from your real cycle, not a nameplate.

Resin moisture versus drying time for a desiccant dryer and a hot-air dryer Line chart of resin moisture content as a percentage against drying time in hours, from zero to six hours, starting at about 0.3 percent. The desiccant-dryer curve falls steeply and crosses below the moldable target line of about 0.02 percent at roughly three hours, continuing down toward 0.005 percent. The hot-air-dryer curve falls at first but flattens out at an equilibrium around 0.05 percent, never reaching the target, because ambient air carries too much moisture. A horizontal dashed line marks the moldable target. 0.300.220.140.060.00 0123456 h drying time (hours) moisture content (%) moldable target β‰ˆ 0.02 % desiccant dryer (βˆ’40 Β°C dew point) hot-air dryer (ambient) plateaus above target desiccant reaches target, then keep to the spec time β€” longer β‰  better (over-drying)
Figure 2. Illustrative drying curves. A desiccant dryer keeps dropping the moisture until it crosses the moldable target; a hot-air dryer flattens out at equilibrium with the ambient air and can stall above target on a humid day β€” which is why hygroscopic resins like PET, PBT, PC and nylon need desiccant drying. Past the target, more time buys nothing and risks over-drying. Curve shapes are schematic, not grade data.

Representative drying conditions used by the calculator

ResinHygroscopic?Temp (Β°C)Time (h)Target moistureDryer
ABSmild80–852–4β‰ˆ 0.1%dry-air / desiccant
PC (polycarbonate)yes115–1253–4β‰ˆ 0.02%desiccant
PA (nylon)very80–854–6β‰ˆ 0.1–0.2%desiccant
PET polyestervery150–1654–6β‰ˆ 0.005%desiccant (βˆ’40 Β°C)
PBT polyestervery120–1403–4β‰ˆ 0.04%desiccant
TPUyes90–1101–3β‰ˆ 0.02–0.05%desiccant
POM (acetal)mild80–1002–3β‰ˆ 0.1%dry-air / desiccant
PP / PEnoβ€”little/nonesurface onlynone (warm air if damp)

Sources for the method. The residence-time sizing rule (hopper capacity = throughput Γ— drying time) is the standard drying-hopper calculation used across molding practice and auxiliary-equipment design. The drying temperatures, times and target-moisture figures are the representative values commonly published on resin-supplier datasheets and processing guides for each polymer family; they are pre-filled as a starting point and every field is editable because the datasheet for your exact grade β€” filled, flame-retardant, high-flow or colored β€” is the authority. The desiccant-versus-hot-air distinction follows from the dew point the air can reach: a hot-air dryer can only dry to equilibrium with ambient humidity, while a desiccant dryer drops the dew point far enough to reach the low targets hygroscopic resins require.

Common mistakes

When to use this calculator vs other methods

MethodUse it whenLimit
This calculatorSizing a dryer or hopper at quoting or line-setup; sanity-checking a supplier's drying setup; teaching why a wet-resin defect appearsRepresentative conditions; assumes steady throughput and a reasonably plug-flow hopper
Resin datasheet / processing guideAny production run in a named gradePer grade; does not size your specific hopper or line
Moisture analyzer / loss-on-heatingConfirming the resin actually reached target before a runA spot sample at one moment, not continuous
In-line dew-point & return-air monitoringVerifying the dryer is holding conditions in productionMeasures the air, infers the pellet state
From the tooling floor: when a part suddenly shows splay or turns brittle mid-run with nothing else changed, check the dryer before you touch the process. A hopper run too low during a busy shift pulls partly dried resin off the bottom; so does a desiccant bed that has quietly stopped regenerating. Keeping the hopper comfortably full β€” the reason for the sizing factor β€” prevents the first, and watching the return-air dew point catches the second.

Questions and answers

How do I size a drying hopper for injection molding?

Use the residence-time rule: required hopper capacity equals the press throughput multiplied by the resin's drying time. Material has to sit in the heated hopper long enough to reach its target moisture before it is molded, so a resin that needs 5 hours of drying at a throughput of 25 kg/h needs a hopper holding about 125 kg. Many molders then add a margin of about 1.5 times so the hopper is never run near empty, because real hoppers are not perfect plug flow. Match the hopper volume in liters to this mass using the resin's bulk density.

Why do hygroscopic resins have to be dried before molding?

Hygroscopic resins such as nylon, PET, PBT, PC, TPU and ABS absorb water into the polymer itself, not just onto the pellet surface. When that wet resin is heated in the barrel the water turns to steam, and in condensation polymers like PET, PBT and nylon it chemically attacks the chains in a reaction called hydrolysis that permanently shortens them and lowers strength. The symptoms are splay or silver streaking, bubbles, brittleness and a drop in molecular weight that cannot be recovered. Drying to the published target moisture is the only cure; a hot barrel cannot drive the water out fast enough.

What temperature should I dry my resin at?

Use the grade's datasheet. Representative published values are roughly 80–85 Β°C for ABS and nylon, 115–125 Β°C for polycarbonate, 120–140 Β°C for PBT, 90–110 Β°C for TPU, 80–100 Β°C for acetal and 150–165 Β°C for PET. The temperature has to be high enough to drive water out of the pellet but below the point where the resin softens, sticks or oxidizes in the hopper.

What is the difference between a desiccant dryer and a hot-air dryer?

A hot-air dryer blows heated ambient air through the hopper and can only dry the resin to equilibrium with the moisture already in that air, so on a humid day it cannot reach the low target that hygroscopic resins need. A desiccant dryer first passes the return air over a desiccant bed that strips the water and drops the dew point to about βˆ’40 Β°C, then reheats that very dry air. Desiccant drying is required for PET, PBT, PC, nylon and TPU; a hot-air or dry-air dryer can suit mildly hygroscopic ABS and acetal in a dry climate; non-hygroscopic PP and PE need no drying.

Can you over-dry plastic resin?

Yes. Leaving resin in a hot hopper far longer than its specified time, or drying it well above the recommended temperature, degrades the polymer just as wetness does. It can oxidize and yellow the resin, break down additives and lubricants, strip plasticizer from flexible grades, and in nylon it can make the melt brittle. Size the hopper to the residence time the resin needs, and if a run stops, turn the heat down so the waiting material is not cooked.

Does PP or PE need to be dried?

Polypropylene and polyethylene are non-hygroscopic and generally need no drying. Any moisture is surface condensation from cold storage, and a short pass of warm air, often about 80 Β°C for under an hour, clears it if the pellets arrive damp. Spending hours drying PP or PE in a desiccant dryer wastes energy and hopper time.

How do I know my resin is dry enough to mold?

The reliable check is a moisture analyzer or a loss-on-heating balance that measures actual moisture against the grade's target β€” for example about 0.005% (50 ppm) for PET, 0.02% for PC and roughly 0.1–0.2% for nylon. The dryer's dew-point readout confirms the air is dry but not that the pellets reached target, and the molded-part symptoms tell you too late. When moisture matters, measure a sample.

Ask JCH about drying your resin

Not sure whether your grade needs a desiccant dryer, or how big a hopper your line needs? Ask our AI assistant. It answers from this website, and our tooling team follows up if you want.

AI assistant. Answers can be wrong; nothing it says is a quote or a promise.

Setting up a new resin on your line?

This calculator gives an engineering estimate of drying conditions and hopper size. Our tooling team reviews the grade's datasheet, the dryer you have and your real throughput, and helps dial in conditions that avoid both wet-resin defects and over-drying. JCH coordinates a vetted manufacturing network.

Book a 30-min call Send a drawing or sample

Reviewed by the JCH tooling team Β· updated November 2026