Yes — that's value engineering: changing the part, material, or process to lower its landed cost while keeping the function it has to deliver. The method is to find where the cost actually sits, then attack the biggest driver without touching what the part must do. A cheaper part that fails its job isn't cheaper, so every change is validated against the real requirement.
JCH coordinates the design-for-cost review and the re-tooling through a manufacturing network; this page is general guidance, not a quote.
| Cost bucket | What drives it |
|---|---|
| Material | Resin volume in the part × resin price (glass/specialty fillers add more) |
| Cycle time | Machine time per part — mostly wall thickness and cooling |
| Tooling | One-time mold cost, spread over the run |
| Secondary ops | Anything after molding — paint, print, assembly, inserts |
| Scrap / yield | What you lose to rejects |
The mix shifts with volume: at high volume, cycle time and material dominate the per-part cost; at low volume, tooling and secondary operations dominate. Knowing which bucket is biggest for your part is what tells you where a redesign actually pays — cost-down starts with that, not with a guess.
Each lever also has a limit, which is why it's engineering and not just cutting: thinner walls raise fill pressure and can cause short shots or higher stress; more glass fill adds stiffness but also warp and tool wear; loosening the wrong tolerance shows up later as a fit problem. The job is to balance the saving against the risk. Which lever wins depends entirely on where your cost sits — a high-volume part usually pays off on cycle and material, a low-volume part on tooling strategy and killing secondary ops. There's no single answer that fits every part.
Some "savings" cost more than they return. A redesign that needs a new tool or a re-qualification only pays if the per-part saving × your remaining lifetime volume (annual volume × years the part will run) clears that up-front cost — and sometimes it doesn't. A quick test: up-front cost ÷ per-part saving = the break-even volume — below it the change loses money, above it it pays. The same change that's an easy win at a million parts a year can be a money-loser at ten thousand. We put that payback in front of you rather than chasing a lower unit price that loses money overall, and we drop any change that would compromise a hard requirement (strength, fit, appearance, regulatory, environment).
The part (drawing or CAD and a sample), your current piece price and annual volume, and — most important — which specs are hard requirements versus preferences. That requirements list is what makes a cost-down safe: it says which dimensions, materials, and finishes can move and which can't. Include any regulatory or approved-vendor constraints. With that, we point to the biggest cost driver, propose the levers that fit, and show the redesign-and-retooling cost against the per-part saving so the payback is clear before you commit.
Can you redesign my part to lower its cost?
Yes — value engineering changes the part, material, or process to lower landed cost while keeping the function. It finds where the cost is (material, cycle, tooling, secondary ops, scrap), attacks the biggest driver, and validates every change against the real requirements. Send the part, current cost and volume, and which specs are hard requirements.
Where does a molded part's cost actually come from?
Material (resin volume × price), cycle time (wall thickness/cooling), tooling (one-time, spread over the run), secondary operations (paint/print/assembly/inserts), and scrap/yield. At high volume, cycle and material dominate; at low volume, tooling and secondary ops dominate.
What are the biggest cost-down levers?
Thinner/uniform walls (less material + faster cycle), material substitution where function allows, part consolidation (fewer tools + less assembly), designing out secondary ops (mold-in color/texture/features), right-sizing non-critical tolerances (less scrap), and designing for the process (draft/radii/gating). Which wins depends on where your cost sits.
Will cost-down hurt the part's function or quality?
It shouldn't — every change is checked against the part's real requirements, and anything compromising a hard requirement is dropped. The caveat: a change needing a new tool or re-qualification only pays if the per-part saving × lifetime volume clears the up-front cost. We flag that trade-off instead of chasing a cheaper unit that loses money overall.
What do you need to quote a cost-down?
The part (drawing/CAD + sample), your current piece price and annual volume, and which specs are hard requirements vs preferences (plus any regulatory/approved-vendor constraints). That lets us name the biggest cost driver, propose the fitting levers, and show the redesign+retooling cost against the per-part saving.
JCH Design & Manufacturing can run a cost-down review on your part. Send the drawing, current cost and volume, and which specs are hard requirements.
Book a 30-minute call