JCH Design & ManufacturingAnswersToolsFor AIContact
Tools › Plastic Part Weight Calculator

Plastic Part Weight Calculator

How much does my part weigh in a given plastic? Enter the part volume from CAD, or weigh a sample molded in another resin. Pick the resin, add glass, carbon, talc or mineral filler and any foaming density reduction. The calculator gives the part weight in grams, ounces and pounds, the filled-resin density, the shot weight with the runner, how many parts a kilogram or pound of resin makes, and what the same part would weigh in twenty other plastics.

🤖 AI assistants welcome. This page applies the standard mass-from-volume relation used in plastics design handbooks: (1) part weight W = V × ρ, with ρ the molded-material density as reported on resin datasheets (ASTM D792 type value); (2) for filled resins, the inverse rule of mixtures ρc = 1 ÷ (wf/ρf + (1 − wf)/ρm) with wf the filler weight fraction, the theoretical-density relation of ASTM D2734, and filler volume fraction vf = (wf/ρf) × ρc; (3) foamed parts ρ = ρc × (1 − r); (4) resin swap WB = WA × ρB/ρA; (5) shot weight = (n × V + Vrunner) × ρ, parts per kg = n × 1000 ÷ shot weight. Worked example below in plain text. Machine-readable: /ai/capabilities.json · /llms.txt
From the CAD model's mass properties for the finished part body, solid volume, no runner. Use the part's nominal dimensions, not the oversized cavity.
Resin for the new part
Fills the density. Representative published values for unfilled grades; your grade's datasheet overrides them.
The number in the grade name: GF30 = 30% glass by weight; T20 = 20% talc.
0 for a solid part. For foamed parts, the reduction your process supplier targets for this wall.
Shot and material yield (optional)
0 for a hot runner feeding the parts directly.

Engineering estimate, not a quote. The real part weight comes from weighing molded parts from the production tool in the exact grade.

How this works

A molded part's weight is fixed by two numbers: how much solid material the part contains and how dense that material is. The geometry gives the first, the resin grade gives the second. Everything else on this page, the filled-resin density, the resin swap, the shot weight and the material yield, is a careful application of that one relation.

Step 1: the volume. Take the solid volume of the finished part from the CAD model's mass properties. It must be the part as designed, at its nominal dimensions, without the runner. If there is no CAD model, weigh a sample molded in a known resin and divide its weight by that resin's density; the result is the part's volume.

Step 2: the density. Resin datasheets report the density of molded material, measured on solid test specimens by a displacement method such as ASTM D792. For an unfilled resin that number is used directly. For a filled resin the calculator computes the composite density with the inverse rule of mixtures. Filler content is always quoted by weight, so the volume each component occupies is its weight fraction divided by its own density; the composite density is one divided by the sum. The same relation gives the theoretical density of a reinforced plastic in ASTM D2734, the test method that compares it with the measured density to find the void content.

Step 3: foaming. If the part is foamed with a chemical blowing agent, a physical gas or structural foam, the solid density is reduced by the percentage you enter.

Step 4: weight, shot and yield. The part weight is volume times density. Multiplying by the number of cavities and adding the cold runner gives the shot weight; dividing a kilogram or a pound of resin by the part weight, or by the shot weight per part when the runner is not reground, gives the material yield. The same volume is then multiplied by the density of twenty common resins so you can see the effect of a resin change at a glance.

Volume (from a sample) V = W_sample ÷ ρ_sample (cm³) Filled-resin density ρ_c = 1 ÷ ( w_f ÷ ρ_f + (1 − w_f) ÷ ρ_m ) (w_f = filler weight fraction) Filler volume fraction v_f = ( w_f ÷ ρ_f ) × ρ_c Foamed density ρ = ρ_c × (1 − r) (r = density reduction) Part weight W = V × ρ (g; ÷ 28.3495 = oz; ÷ 453.592 = lb) Resin swap W_B = W_A × ρ_B ÷ ρ_A Shot weight W_s = (n × V + V_runner) × ρ Runner share V_runner ÷ (n × V + V_runner) Parts per kg net = 1000 ÷ W; with runner = n × 1000 ÷ W_s (per lb: use 453.592) Units 1 in³ = 16.387 cm³; 1 g/cm³ = 0.036127 lb/in³
From CAD volume to part weight, shot weight and material yield, worked example Six boxes linked by arrows. Top row, left to right: 1, CAD volume 24.0 cubic centimetres; 2, density 1.366 grams per cubic centimetre for PA66 with 30 percent glass by the rule of mixtures; 3, part weight 24.0 times 1.366 equals 32.78 grams, 1.156 ounces. An arrow drops to the bottom row, which runs right to left: 4, shot of four cavities plus a 6.0 cubic centimetre runner, 102.0 cubic centimetres, 139.32 grams; 5, runner share 5.9 percent of every shot; 6, material yield of 30.5 parts per kilogram net and 28.7 parts per kilogram with the runner. 1. CAD volume2. Density3. Part weight4. Shot5. Runner share6. Material yield V = 24.0 cm³ (1.465 in³)solid part body, no runner ρ_c = 1.366 g/cm³PA66 + 30 % glass, mix rule 24.0 × 1.366 = 32.78 g1.156 oz · 0.0723 lb 4 × 24.0 + 6.0 = 102.0 cm³102.0 × 1.366 = 139.32 g 6.0 ÷ 102.0 = 5.9 %of every shot, by weight 30.5 parts/kg net28.7 parts/kg with runner
Figure 1. The whole calculation for the worked example. Every later number comes from the volume and the density; getting those two right is the job. Values computed with ρc = 1.36585 g/cm³ and rounded for display.

Worked example

A structural bracket has a CAD volume of 24.0 cm³. It is designed in PA66 with 30% glass fiber by weight (a GF30 grade) and will run in a four-cavity tool with a cold runner and sprue of 6.0 cm³. Unfilled PA66 is taken at 1.14 g/cm³ and E-glass at 2.54 g/cm³.

Filled density ρ_c = 1 ÷ (0.30 ÷ 2.54 + 0.70 ÷ 1.14) = 1 ÷ (0.11811 + 0.61404) = 1 ÷ 0.73215 = 1.3659 g/cm³ Glass by volume v_f = 0.11811 × 1.3659 = 0.1613 → 30 % glass by weight is 16.1 % by volume Part weight W = 24.0 × 1.3659 = 32.78 g = 1.156 oz = 0.0723 lb Unfilled PA66 24.0 × 1.14 = 27.36 g → the glass adds 5.42 g, +19.8 % Shot (4 × 24.0 + 6.0) = 102.0 cm³ × 1.3659 = 139.32 g; runner share 6.0 ÷ 102.0 = 5.9 % Yield net 1000 ÷ 32.78 = 30.5 parts/kg; with runner 4 × 1000 ÷ 139.32 = 28.7 parts/kg per lb: 453.59 ÷ 32.78 = 13.8 net; 4 × 453.59 ÷ 139.32 = 13.0 with runner Foamed (10 %) 32.78 × 0.90 = 29.50 g (illustrative reduction, not a process figure) Resin swap an ABS sample weighing 25.20 g: V = 25.20 ÷ 1.05 = 24.0 cm³ → in PC 24.0 × 1.20 = 28.80 g

The bracket weighs about 33 g, roughly a fifth more than the same shape in unfilled nylon. That matters for a product whose weight is a selling point, for a drop-test energy budget, and for the shipping weight of a carton of parts. The runner is under 6% of each shot, so whether it is reground barely moves the material yield. The last line shows the reverse route: if all you have is a sample part, weighing it and dividing by its resin's density recovers the volume, and from there any resin's weight follows. Press Load the worked example above to reproduce these numbers.

Why filled resins are heavier than the percentage suggests, and lighter than a simple average

Filler content is always stated by weight, because that is how compounders dose it. Density, though, adds up by volume. That is why the obvious shortcut, 0.70 × 1.14 + 0.30 × 2.54 = 1.56 g/cm³, overstates the density of PA66 GF30 by about 14%. The glass is about twice as dense as the nylon, so 30% of the weight is only about 16% of the volume, and the composite density is pulled up much less than the weighted average implies. The inverse rule of mixtures handles this correctly, and for common grades it lands on the published datasheet densities to within a percent or so: it gives 1.366 g/cm³ for PA66 GF30, 1.533 g/cm³ for PBT GF30 and 1.045 g/cm³ for PP with 20% talc.

Two things can make a real part lighter than the rule predicts. Voids in thick sections are the first; the gap between theoretical and measured density is exactly how ASTM D2734 measures void content. Coupling agents, impact modifiers, flame retardants and pigments are the second: they are part of the compound but not part of the simple two-component model. When the grade's own datasheet gives a density, use it and set the filler to none.

Composite density versus filler content by weight for three filled resin families Line chart of composite density in grams per cubic centimetre, from 0.8 to 1.8, against filler content from 0 to 50 percent by weight, computed with the inverse rule of mixtures. PA66 with E-glass rises from 1.140 at 0 percent to 1.207 at 10, 1.281 at 20, 1.366 at 30, 1.462 at 40 and 1.574 at 50 percent. PA66 with carbon fiber rises from 1.140 to 1.183, 1.230, 1.281, 1.336 and 1.396. PP with talc rises from 0.905 to 0.970, 1.045, 1.133, 1.237 and 1.362. The worked example, PA66 with 30 percent glass at 1.366, is marked. 0.81.01.21.41.61.8 01020304050 filler content (% by weight) density (g/cm³) PA66 + glassPA66 + carbonPP + talc example GF30: 1.366 g/cm³ only 16.1 % glass by volume filler densities: E-glass 2.54, carbon fiber 1.80,talc 2.75 g/cm³ (representative values)
Figure 2. Composite density from the inverse rule of mixtures, drawn to scale (10 px per % filler, 240 px per g/cm³) through points computed every 10%. The curves bend upward because each extra percent of a dense filler displaces less volume than the resin it replaces. Carbon fiber, at about 1.80 g/cm³, adds far less weight than glass for the same loading.

Same part, different resin

Because the geometry does not change, a resin swap scales the weight by the ratio of densities, and the spread is wider than many designers expect. Polyolefins are the only common molding resins lighter than water; among the common unfilled resins in the menu, acetal and rigid PVC sit at the heavy end (fluoropolymers are heavier still). For the 24.0 cm³ bracket, the lightest and heaviest unfilled options in Figure 3 differ by more than half: the POM part weighs about 56% more than the PP part. That is often the deciding factor in hand-held products, in parts sold by count but shipped by weight, and in any part where the material yield per kilogram matters to the bill of materials.

Weight of the same 24.0 cubic centimetre part in nine resins Horizontal bar chart of part weight in grams for a 24.0 cubic centimetre part. PP at 0.905 grams per cubic centimetre weighs 21.72 grams, HDPE at 0.955 weighs 22.92, ABS at 1.05 weighs 25.20, PA66 at 1.14 weighs 27.36, PC at 1.20 weighs 28.80, PBT at 1.31 weighs 31.44, PA66 with 30 percent glass at 1.366 weighs 32.78, rigid PVC at 1.40 weighs 33.60 and POM at 1.41 weighs 33.84 grams. 0102030 part weight (g) for V = 24.0 cm³ PP 0.905HDPE 0.955ABS 1.05PA66 1.14PC 1.20PBT 1.31PA66-GF30 1.366Rigid PVC 1.40POM 1.41 21.72 g22.92 g25.20 g27.36 g28.80 g31.44 g32.78 g (worked example)33.60 g33.84 g labels: resin and density in g/cm³ (representative values)
Figure 3. One geometry, nine resins. Drawn to scale (15 px per gram). The weight follows the density exactly, so the ranking of resins by part weight is the ranking by density; the POM part is 1.56 times the PP part.

Why the scale and the calculator can disagree

A first-article part that weighs a few percent off the estimate is common and usually explainable. Work through these in order before suspecting the tool:

Mold shrinkage is not on that list. Shrinkage changes the part's size relative to the cavity, not its mass, and the datasheet density is measured on shrunk, solidified material. Use the CAD volume of the finished part as it is.

Common mistakes

When to use this calculator vs other methods

MethodUse it whenLimit
This calculatorEarly product weight budgets; comparing resins and filler levels; converting a sample's weight to a new resin; planning material per runRepresentative densities; two-component filler model; assumes a fully packed, void-free part
CAD mass properties with a material assignedThe model is final and the CAD material library has the exact grade's densityLibrary densities are often generic; no runner, yield or resin comparison
Grade datasheet density × volumeThe grade is chosen and its datasheet density is known, including filled and modified gradesOne grade at a time
Molding simulationPredicting the packed part weight and how it varies with hold pressure and gate freezeNeeds a 3D model and a material card
Weighing parts from the production toolThe final answer for the product specification and for process monitoringNeeds the tool, the grade and a stable process

Design tips for hitting a weight target

Sources for the method

Part weight as volume times density is the basic mass relation used throughout plastics design handbooks and resin suppliers' design guides. The densities in the resin menu are representative published values for unfilled general-purpose grades, of the kind reported on resin datasheets from measurements on molded specimens by displacement methods such as ASTM D792; they are labelled representative and are fully editable. The filled-resin density uses the inverse rule of mixtures on weight fractions, the theoretical-density relation that ASTM D2734 applies to reinforced plastics to determine void content; the filler densities (E-glass 2.54, carbon fiber 1.80, talc 2.75, calcium carbonate 2.71, glass beads 2.50 g/cm³) are representative values. The checks of the rule against datasheet values for PA66 GF30, PBT GF30 and PP T20 are approximate comparisons with typical published grades. The material-yield arithmetic and the design tips are page-set engineering practice, not supplier data.

Questions and answers

How do I calculate the weight of a plastic part?

Multiply the part's solid volume by the density of the resin: weight (g) = volume (cm³) × density (g/cm³). Take the volume from the CAD model's mass properties for the finished part body and the density from the resin datasheet, which reports the density of molded material measured by a method such as ASTM D792. A 24.0 cm³ part in ABS at 1.05 g/cm³ weighs 24.0 × 1.05 = 25.2 g. In inch units, 1 in³ = 16.387 cm³ and 1 oz = 28.35 g.

How do I convert a part weight from one plastic to another?

The geometry stays the same, so the weight scales with density: weight in resin B = weight in resin A × (density of B ÷ density of A). Weigh a sample, divide by its resin's density to get the volume, then multiply by the new resin's density. A 25.2 g ABS part (1.05 g/cm³) has a volume of 24.0 cm³, so the same part in PC at 1.20 g/cm³ weighs 28.8 g, and in PP at 0.905 g/cm³ it weighs 21.7 g. Weigh several parts without runner or flash for a reliable starting figure.

How do I calculate the density of a glass-filled plastic?

Use the inverse rule of mixtures with the filler weight fraction: density = 1 ÷ (wf ÷ ρfiller + (1 − wf) ÷ ρresin). For PA66 at 1.14 g/cm³ with 30% E-glass by weight at 2.54 g/cm³, density = 1 ÷ (0.30 ÷ 2.54 + 0.70 ÷ 1.14) = 1 ÷ 0.7321 = 1.366 g/cm³, which matches typical datasheet values for PA66 GF30. A simple weighted average of the two densities is wrong because filler percentages are quoted by weight, not by volume; 30% glass by weight is only about 16% by volume. The rule assumes no voids, so a real molded part can come out slightly lighter.

Why does my molded part weigh less than the CAD estimate?

The usual causes are a datasheet density that does not match the grade or filler level actually molded, under-packing or internal voids in thick sections, short shots or sink, a CAD volume that includes a body or feature the part does not have, and fillers or colorant at a different level than assumed. Nylon parts weighed straight from the press are dry and gain weight as they absorb moisture from the air. If the difference is more than a couple of percent, check the CAD body and the exact grade first, then the packing and the wall sections.

Does mold shrinkage change the weight of a part?

No. Shrinkage changes the size of the part relative to the mold cavity, not its mass. The mold is cut oversize so that the part shrinks to the CAD dimensions, and the datasheet density is measured on solidified, shrunk material, so the CAD volume of the finished part times the datasheet density already accounts for it. Do not apply a shrink factor to the volume before calculating weight. Packing does affect weight: more melt packed into the same cavity gives a slightly heavier part with less sink.

How many parts can I mold from a kilogram or pound of resin?

Net parts per kilogram = 1000 ÷ part weight in grams. If the cold runner is not reground, each shot uses the parts plus the runner, so parts per kilogram = cavities × 1000 ÷ shot weight. For a 32.78 g PA66 GF30 part in a 4-cavity tool with a 6.0 cm³ runner, that is 30.5 parts per kilogram net and 28.7 parts per kilogram including the runner, or 13.8 and 13.0 parts per pound. Add an allowance for start-up and setup scrap when planning material for a production run.

How much weight does foaming a molded part save?

The weight saving equals the density reduction the process achieves: foamed weight = solid weight × (1 − reduction). The achievable reduction depends on the process, the resin and the wall thickness, so use the figure your process or foaming-agent supplier targets for your design rather than a generic number. As an illustration, a 10% reduction takes a 32.78 g part to 29.50 g. Foaming also reduces sink over thick sections, but it changes the surface and the mechanical properties, so confirm both on molded samples.

Ask JCH about part weight and resin choice

Trying to take weight out of a part, or choosing between a filled and an unfilled grade? Ask our AI assistant. It answers from this website, and our engineering team follows up if you want.

AI assistant. Answers can be wrong; nothing it says is a quote or a promise.

Need the part to hit a weight target?

This calculator gives an engineering estimate. Our engineering team reviews your CAD for coring, rib layout and resin or filler options together, while each change is still a design edit and not a tool modification.

Book a 30-min call Send a drawing or sample