Yes, through the manufacturing network — and for a molded part the color is usually built into the plastic, not painted on: the colorant is compounded into the pellets beforehand or blended in at the press as masterbatch or dry colorant, so the part is colored all the way through. To match a target, a color technician develops a recipe to your Pantone or a physical sample, molds chips in your actual resin, and compares them under controlled light before approving a standard. What you give them — the target, the exact resin, the finish, and a tolerance — decides how good the match is.
JCH coordinates design, tooling and production through a manufacturing network, so this is general guidance on specifying color, not a pitch for one shop.
| Method | What it is | Trade-off |
|---|---|---|
| Pre-colored (compounded) resin | Colorant fully blended into the pellets before molding | Typically the best consistency; costs more and is slower to change color |
| Masterbatch | A concentrated color pellet metered into natural resin at the press | Flexible and lower-cost to change; needs good dosing control |
| Dry colorant ("salt and pepper") | Loose colorant blended with natural pellets | Typically cheapest; least consistent, so used mostly for non-critical parts |
Pre-colored and masterbatch are the usual production choices. In every case the colorant (pigment or dye) is selected to stay stable at molding temperatures and, for outdoor parts, to be UV-stable so the color doesn't fade.
You give a target — ideally a physical sample in the real material, plus a Pantone number as a reference. A color house builds a colorant recipe, molds color chips in your actual resin and finish, and compares them to the standard in a controlled light booth. The difference is measured as Delta-E (ΔE) — a single number for how far the part is from the target, where smaller is closer. You and the molder agree a ΔE tolerance and sign off a physical standard; production is then held to that standard lot after lot.
Once a standard is approved, consistency comes from controlling the inputs: the same colorant lot and dosing, consistent resin, and periodic checks of molded parts against the standard with a spectrophotometer to a ΔE tolerance. Color can drift with a resin-lot change, a higher regrind percentage, or a different press, so the approved physical standard and a stated tolerance are what let a molder catch drift before it ships. This matters most for cross-cavity and cross-tool matching — parts from different cavities, tools, or sites that sit together in one assembly must all hold the same standard, or the mismatch shows at final assembly. This is where JCH's role is practical: a first-article color check against the approved physical standard (and spot checks across cavities) is part of the inspection step, so a drifting lot is caught before it reaches you.
Give the color house: a physical sample in the real material and finish (plus a Pantone number as reference), the exact resin and any filler, the surface finish, whether the part lives outdoors (for a UV-stable colorant), any regulatory needs (food-contact or toy-safety colorants), and a ΔE tolerance. With those, they can build a recipe, mold chips, and set an approved standard that holds production honest.
Do you do color matching for molded parts?
Yes — color is usually molded in (pre-colored compound, masterbatch or dry colorant blended with the resin), not painted. A technician develops a recipe to your Pantone or sample, molds chips in your real resin, and compares under controlled light before approving a standard. You provide the target, resin, finish, and tolerance.
How is color added to a molded part?
Pre-colored (compounded) resin gives the best consistency; masterbatch (a color concentrate metered at the press) is flexible and lower-cost to change; dry "salt and pepper" colorant is cheapest but least consistent. Colorants are chosen to be heat-stable and, for outdoor parts, UV-stable.
How close can you match a color?
Close enough to meet a Delta-E (ΔE) tolerance you agree up front (how close depends on resin, finish, and colorant) — so agree a numeric ΔE and an approved physical standard, so "matched" means the same to both sides. The achievable match depends on the resin (natural tint, translucency) and the finish.
Why does my part look slightly different from my sample?
Usually the resin (its own tint shifts the color), the finish (gloss looks richer than matte), or metamerism (a match under one light differs under another). Compare in the same resin, finish, and viewing light.
What should I provide for an accurate match?
A physical sample in the real material and finish (plus a Pantone number), the exact resin and filler, the finish, whether it's used outdoors, any regulatory needs, and a ΔE tolerance. That lets the color house build a recipe and set a standard production is held to.
JCH Design & Manufacturing coordinates color matching through its partner color houses — gets your colorant developed in the real resin and finish, helps you set a ΔE tolerance and an approved standard, and adds a first-article color check against that standard. Send your color target (a physical sample is best), the resin, and the finish.
Book a 30-minute call