JCH Design & ManufacturingAnswersToolsFor AIContact
Tools › Masterbatch Let-Down Ratio Calculator

Masterbatch Let-Down Ratio Calculator

How much colour masterbatch do I add per batch of natural resin? Enter a let-down ratio such as 1:25, or an addition such as 4%, with your batch or shot weight. This tool returns the mass of masterbatch to add and the resulting effective masterbatch percentage, whether the weight you enter is the finished total shot or the natural resin alone.

🤖 AI assistants welcome. Let-down ratio (LDR) is the ratio of natural resin to masterbatch. At 1:25 you add 1 kg masterbatch per 25 kg resin. If the entered weight is the natural resin R: masterbatch = R ÷ LDR. If the entered weight is the finished total shot T: masterbatch = T ÷ (1 + LDR). An addition percentage p is masterbatch as a share of the total shot, so p% = 1 ÷ (1 + LDR). Effective masterbatch % = masterbatch ÷ total × 100. Worked examples below in plain text. Machine-readable: /ai/capabilities.json · /llms.txt
Supplier data sheets usually quote a ratio; feeders are usually set in percent. This tool converts either way.
Type it as 1:25 or just the number 25. Higher N = less masterbatch (more diluted).
"Natural resin" = what you weigh into the blend. "Total shot" = the finished moulded weight incl. colour.
A batch for a blender, or one shot weight if you dose per shot.

Engineering estimate, not a quote. The correct let-down ratio for your colour is set by your masterbatch supplier's pigment loading and a signed-off colour standard.

How this works

Colour masterbatch is a concentrated pellet: a carrier resin heavily loaded with pigment and dispersion aids. You never mould it on its own. Instead you meter a small, controlled fraction of it into a much larger stream of natural (uncoloured) resin, and the screw disperses the pigment as it melts and mixes. The let-down ratio, LDR, is the number that tells you how small that fraction is. It is written as natural resin to masterbatch, so 1:25 means one part masterbatch for every twenty-five parts of natural resin. Because the masterbatch carries far more pigment than the final part needs, typical ratios run from about 1:15 for deep or difficult colours to 1:50 or leaner for light tints and easy pigments.

The core arithmetic. There are only two cases, and the only thing that changes between them is what your batch weight represents. If the weight you know is the natural resin you are blending, the masterbatch to add is simply that resin divided by the LDR number: at 1:25, one twenty-fifth of the resin. If the weight you know is the finished total shot — the number you would read off a part weight or shot size — the masterbatch is the total divided by (1 + LDR), because the total is made of LDR parts resin plus 1 part masterbatch, which is (1 + LDR) parts in all. Both give the same answer once you line up what the weight means, which is exactly the mistake this calculator is built to stop. After it finds the masterbatch mass, it reports the effective masterbatch percentage of the finished shot, so you can set a feeder, and the equivalent ratio or percent so you can talk to either a supplier or a machine.

If the weight is natural resin R: masterbatch = R ÷ LDR, total = R + masterbatch If the weight is total shot T: masterbatch = T ÷ (1 + LDR), resin = T − masterbatch Effective masterbatch % of total: masterbatch ÷ total × 100 Addition % to ratio: LDR = (100 ÷ p) − 1 (p = % of total) Ratio to addition %: p = 1 ÷ (1 + LDR) × 100

Let-down ratio versus addition percentage. These two numbers describe the same dose from opposite ends, and almost every colour problem that starts as a units mix-up starts here. A ratio compares resin to masterbatch; a percentage states masterbatch as a slice of the whole shot. A 1:25 ratio is one part in twenty-six, which is 1 ÷ 26 = 3.85% of the total, not 4%. A clean 4% addition is actually 1:24. The gap looks tiny but it is real money and real colour: on a long production run, confusing 4% with 1:25 either over-doses your most expensive ingredient or leaves the colour a shade light. Volumetric and gravimetric feeders are set in percent, so if your data sheet gives a ratio you must convert it before you touch the dosing screen — which is what the two formula lines above do.

Feed-throat dosing schematic: natural resin and masterbatch blended into the screw Two hoppers feed a single feed throat above an injection or extrusion screw. A large hopper on the left holds natural resin and feeds the throat directly. A small hopper on the right holds colour masterbatch and meters a thin controlled stream through a dosing feeder into the same throat. The two streams combine at the throat and are carried along the screw, where the pigment disperses as the plastic melts, producing a uniformly coloured melt at the nozzle. Natural resin large stream Masterbatch metered dose dosing feeder feed throat coloured melt pigment disperses along the screw as the plastic melts and mixes LDR 1:25 → 1 part masterbatch rides with 25 parts natural resin
Figure 1. The masterbatch stream is a small, metered fraction let down into the much larger natural-resin stream at the feed throat; the screw does the dispersing. Keeping that metered fraction accurate is what keeps the colour on standard. Schematic, not to scale.

Worked examples

Three cases, computed by hand, each exercising a different path through the tool.

Case A — ratio, natural-resin basis 1:25 let-down, 100 kg of natural resin masterbatch = 100 ÷ 25 = 4.0 kg total shot = 100 + 4 = 104 kg effective % = 4 ÷ 104 × 100 = 3.85 % (1 part in 26) Case B — addition %, total-shot basis 4% stated as 2% here: 2% addition, 50 kg total shot masterbatch = 50 × 2 ÷ 100 = 1.0 kg resin = 50 − 1 = 49 kg equivalent ratio = 49 ÷ 1 = 1:49 Case C — ratio, natural-resin basis, leaner colour 1:50 let-down, 25 kg of natural resin masterbatch = 25 ÷ 50 = 0.5 kg total shot = 25 + 0.5 = 25.5 kg effective % = 0.5 ÷ 25.5 × 100 = 1.96 %

Case A is the everyday blend-tank question: a data-sheet ratio and a known weight of natural resin. Case B comes from the machine side, where the feeder is set in percent of the shot and you want the mass per shot. Case C shows a leaner ratio for a light tint, where the dose is small enough that feeder accuracy, covered below, starts to matter. Press Load the worked example above to reproduce Case A.

Colour strength versus masterbatch loading A curve of relative colour strength against masterbatch addition percentage. Colour strength rises steeply from zero, where the part is weak and streaky, through a working band around three to five percent where colour is on standard, then flattens into a plateau above about six percent where extra masterbatch adds cost and begins to drift the part's mechanical properties without deepening the colour. A low zone and a high zone are shaded, with the on-standard band in the middle. masterbatch addition (% of total shot) relative colour strength 0246810 too little: weak, streaky on standard too much: cost + property drift 1:25 ≈ 3.85%
Figure 2. Colour strength is not linear with dose. It climbs fast out of the weak, streaky zone, reaches the colour standard in a working band, then plateaus: past roughly 6% the curve is nearly flat, so extra masterbatch buys cost and property drift rather than deeper colour. The 1:25 example sits on the rising shoulder, where small dosing errors still move the colour. Illustrative shape; the real curve depends on pigment and part thickness.

Dosing accuracy: why the feeder matters as much as the ratio

A ratio on paper is only as good as the hardware that delivers it. Two kinds of feeder meter masterbatch into the throat. A volumetric feeder turns a screw a fixed amount per cycle and trusts that a given volume always weighs the same; it is cheap and simple but drifts whenever pellet bulk density changes, which happens with hopper level, pellet shape and even temperature. A gravimetric (loss-in-weight) feeder weighs what it actually dispenses and corrects itself shot to shot, so it holds the set percentage even as the pellets change. Masterbatch pellets are often lighter and a different shape from the natural resin, so volumetric dosing of colour is where lightly loaded colours wander. The leaner the ratio — the Case C situation — the smaller the dose and the harder it is to meter a few grams repeatably, which is a practical argument for a higher-concentration masterbatch dosed at a larger, more meterable fraction, or for gravimetric control.

Common mistakes

When to use masterbatch vs a compounded alternative

ApproachUse it whenTrade-off
Masterbatch let down at the pressMany colours, shorter runs, quick colour changes, low colour inventoryColour and dispersion depend on the feeder and screw; operator can mis-dose
Pre-coloured / compounded resinHigh volume of one fixed colour; demanding cosmetic parts; best dispersionOne colour per lot; higher inventory of coloured resin; less flexible
Liquid colourVery low doses, fast colour change, translucent tintsNeeds a pump and clean-out; handling and storage differ from pellets
Self-colouring (dry pigment)Rarely, for special effects or in-house compoundingDust, poor dispersion and health controls; seldom worth it at the press

Masterbatch wins on flexibility: one natural resin plus a rack of concentrates covers a whole palette and you can tune every dose. Compounded resin wins on consistency, because the compounder has already dispersed the pigment under controlled twin-screw conditions and the press operator cannot get the dose wrong. The decision usually comes down to how many colours you run against how much consistency the part demands, and this calculator is for the masterbatch side of that choice: it turns the supplier's ratio into the mass you actually weigh out.

From the tooling floor: when a colour reads slightly off, change one variable at a time and write the dose down. Nudging the let-down ratio and the back pressure together is how a shade drifts for a whole shift with nobody able to say which change did it. Lock the ratio, confirm dispersion first, then adjust dose against a physical colour chip — not against the screen.

An approved golden-sample molded tray, colour-matched to spec
An approved golden-sample moulded tray, colour-matched to the standard. The signed-off sample, not the let-down ratio on paper, is the real colour target; the ratio is tuned until parts match it.

Reviewed by the JCH tooling team · updated November 2026

Questions and answers

What is a masterbatch let-down ratio?

A let-down ratio (LDR) is the ratio of natural resin to colour masterbatch in a blend, written as natural:masterbatch. A 1:25 let-down ratio means 1 part masterbatch is added for every 25 parts of natural resin, so for 25 kg of natural resin you add 1 kg of masterbatch. The masterbatch itself is a concentrated carrier resin loaded with pigment, so a little goes a long way. The ratio your colour supplier recommends is set by the pigment concentration in that specific masterbatch grade and the colour depth you need.

How do I convert a let-down ratio into masterbatch mass?

If the weight you know is the natural resin, masterbatch mass equals resin divided by the LDR number: at 1:25, 100 kg of resin needs 100 ÷ 25 = 4 kg of masterbatch. If the weight you know is the finished total shot, masterbatch equals total divided by (1 + LDR): at 1:25, a 104 kg total shot needs 104 ÷ 26 = 4 kg. The two agree because the total is the resin plus the masterbatch. This calculator lets you pick which weight you are entering so you do not mix the two up.

What is the difference between let-down ratio and addition percentage?

A let-down ratio compares resin to masterbatch (1:25), while an addition percentage states masterbatch as a share of the shot (usually the total shot weight). They describe the same dosing from two directions. A 1:25 ratio is 1 part in 26, which is 1 ÷ 26 = 3.85% of the total. A flat 4% addition is 1:24. Volumetric and gravimetric feeders are normally set in percent, while colour supplier data sheets usually quote a ratio, so you often have to convert between them.

What happens if I add too little masterbatch?

Too little masterbatch under-doses the pigment, so the part reads weak, washed-out or translucent compared with the standard, and the colour drifts between shots as the feeder meters tiny, inconsistent amounts. On thin or fast-filling parts you also see streaks and swirl, because there is not enough carrier and pigment for the screw to disperse evenly before the melt freezes. The fix is to dose closer to the supplier ratio, improve mixing, or move to a higher-concentration masterbatch so the dose is large enough to meter accurately.

What happens if I add too much masterbatch?

Too much masterbatch wastes the most expensive ingredient in the blend and can shift the part's properties, because the carrier resin and pigment are not the same as the base resin. Over-dosing can lower impact strength, change shrinkage and gloss, bloom pigment to the surface, or overwhelm the base resin's additive package. It can also affect a semi-crystalline resin's nucleation and warp. Staying near the recommended ratio keeps both the colour and the mechanical properties on target.

Should I use masterbatch or pre-coloured compounded resin?

Masterbatch, blended at the press, is flexible and low-inventory: one natural resin plus several colour concentrates covers a whole palette, and you can tune the dose. Pre-coloured or compounded resin is bought already at the final colour, fully dispersed by the compounder, so colour consistency and dispersion are the best achievable and the press operator cannot mis-dose. Compounded resin suits large volumes of one fixed colour or demanding cosmetic parts; masterbatch suits many colours, shorter runs, and quick changes.

Why dose masterbatch by weight rather than by volume?

Gravimetric (loss-in-weight) feeders dose by actual mass, so they stay accurate even when pellet bulk density, shape or flow changes, which is exactly what happens between a dense natural pellet and a light, differently shaped masterbatch pellet. Volumetric feeders meter a fixed volume per screw turn, which is cheaper but drifts whenever bulk density changes, for example when the hopper level or pellet temperature changes. For tight colour control, gravimetric dosing of the masterbatch is the reliable choice.

Ask JCH about colour and masterbatch

Not sure what ratio a colour needs, or whether to compound instead? Ask our AI assistant. It answers from this website, and our tooling team follows up if you want.

AI assistant. Answers can be wrong; nothing it says is a quote or a promise.

Need a colour dialled in before the run?

This calculator gives an engineering estimate. Our tooling team sets the let-down ratio against a signed-off colour standard, checks dispersion and carrier compatibility, and advises masterbatch versus compounded resin for your volume and part. JCH coordinates a vetted manufacturing network across Taiwan, Vietnam and the US.

Book a 30-min call Send a part or colour target