Yes — and it comes from the mold, not a separate step on each part. The surface of the steel is transferred to every part, so a high-gloss polish, a satin finish, a matte bead-blast, or a grained texture is applied to the tool once and then carried by everything it makes. The choices that matter: where the finish goes (usually the cosmetic faces), how glossy or matte it is, and whether the design has enough draft to release it cleanly.
JCH coordinates design, tooling and production through a manufacturing network, so this is general guidance on specifying a finish, not a pitch for one shop.
| Finish family | Look / feel | How it's made in the tool |
|---|---|---|
| SPI A (A1–A3) — high gloss | Mirror / piano-black; lenses, cosmetic housings | Progressive diamond polishing to a mirror (A1 ≈ #3 diamond buff) |
| SPI B (B1–B3) — semi-gloss | Satin sheen; general consumer parts | Fine wet-sanding (B1 ≈ 600-grit paper) |
| SPI C (C1–C3) — matte stone | Flat, low-reflection matte | Stone finishing of the steel (C1 ≈ 600 stone; C3 ≈ 320 stone) |
| SPI D (D1–D3) — dry-blast matte | Fine to coarse matte, grippy | Dry/bead blasting with finer-to-coarser media (D1–D3; e.g. glass bead or aluminum-oxide grit) |
| Textures (VDI 3400 / Mold-Tech) | Leather grain, geometric, patterns matched to a sample | EDM spark-erosion (VDI 3400, e.g. VDI 24–33), chemical etching, or laser texturing; Mold-Tech patterns called out as MT-xxxxx |
You can combine them on one part — a polished window inside a textured body — as long as each region is called out on the drawing. A real call-out looks like: "Housing exterior: Mold-Tech MT-11010; lens window: SPI A2." The right finish balances how the part should look and feel against how cleanly it releases from the tool.
The texture is put into the mold steel, not onto the part: a gloss comes from polishing the cavity to a mirror, a matte from bead-blasting, and a grain from EDM spark-erosion (the VDI 3400 scale), chemical etching, or laser-texturing. Because it lives in the tool, every part carries it with no per-part finishing step — efficient at volume, though the texturing itself adds tool cost and lead time, and a textured tool is hard to re-polish or revise. So changing a finish is a tool change: settle it before the steel is cut, because a late switch from matte to high-gloss, or a deeper texture, can mean re-working or re-cutting the cavity.
A mold texture is molded in — permanent, with no per-part finishing step once the tool exists (the texturing is a one-time tool cost), and limited to what can be cut into steel. A secondary finish is applied after molding — painting, pad printing or silkscreen, plating, or in-mold decoration — and adds color, graphics, or effects the tool can't make, at a per-part cost and an extra step. Many parts use both: a molded-in texture plus printed graphics. Decide early which look must come from the tool and which from a secondary process, because it changes both the tool and the cost.
Give the molder: the SPI grade or texture number (or a physical sample to match), which surfaces it applies to (call out cosmetic faces vs. non-visible areas), whether any area needs a different finish, and confirmation that the draft suits the chosen texture. A sample part or a drawing with the finish called out per surface is the surest way to get the look you expect on the first tool.
Can you add a surface texture or finish to a molded part?
Yes — it comes from the mold, applied to the steel once and carried by every part. Specify a high-gloss polish, a satin or matte finish, or a grained texture, note which faces it applies to, and make sure the design has enough draft to release it.
What finishes are available — gloss, matte, or textured?
The SPI scale is the common reference: A = high-gloss polish, B = semi-gloss, C = matte stone, D = dry-blast matte. Texture libraries (VDI, Mold-Tech) add leather grains and patterns matched to a sample. You can mix finishes on one part if each area is called out.
How is the texture actually created?
It's put into the mold steel: polishing for gloss, stoning or bead-blasting for matte, EDM, etching or laser texturing for a grain. Because it lives in the tool, every part carries it with no secondary step — but a texture change is a tool change, so settle it before cutting steel.
Does the finish affect how I design the part?
Yes — a texture needs more draft to release (deeper texture, more draft), and a high-gloss finish shows sink and flow marks while a matte texture hides them. So glossy parts demand more uniform walls and careful gating; texture can mask minor cosmetic variation.
What's the difference between a mold texture and a secondary finish like paint?
A mold texture is molded in — permanent, with no per-part finishing step (a one-time tool cost), but limited to what can be cut into steel. A secondary finish (paint, pad print, plating, in-mold decoration) is applied after molding for color or graphics the tool can't make, at a per-part cost. Many parts use both.
JCH Design & Manufacturing can help you choose and specify the right finish — gloss, matte, or a matched texture — check that your draft suits it, and decide what should be molded-in vs. a secondary step. Send a sample, drawing, or description; NDA first.
Book a 30-minute call