Yes — JCH coordinates POP and retail displays through a manufacturing network: countertop and floor units, PDQ trays, end-caps, standees, and the molded, fabricated, and printed parts that make them. A display is a mix of processes — molded and fabricated parts, printed graphics, and assembly — built to one spec so the finished unit ships flat where the structure allows, kitted with its graphics and instructions, and goes up with minimal tools in-store.
JCH coordinates the molding, fabrication, print, and assembly through the network; this page is general guidance, not a quote.
| Process / material | Used for |
|---|---|
| Corrugated + print | Temporary promotional displays; low cost, light, recyclable |
| Injection-molded | Custom bins, hooks, and bases at volume for permanent fixtures |
| Thermoformed | Lighter trays and shells, lower tooling cost |
| Acrylic / PETG | Clear, premium fronts and holders (fabricated and bent) |
| Metal wire / sheet | Shelving and hooks that carry weight |
Most real displays combine several — a molded base, a metal upright, acrylic fronts, applied graphics — so most displays are built to one coordinated spec and shipped together where the structure allows.
| Temporary | Permanent | |
|---|---|---|
| Material | Corrugated, printed | Molded, metal, acrylic |
| Life | Weeks to months | Months to years |
| Cost | Low up front | Higher up front |
| Fits | A promotion | An ongoing fixture |
A permanent display only pays off if it stays up long enough to earn back its higher cost, so a short promotion wants temporary and an ongoing presence wants permanent. Many brands run a temporary version to test placement, then invest in a permanent one where it performs.
Every display runs on two clocks. The shopper's clock is seconds — the unit has to read and sell in the moment someone walks past, so the hero product, the message, and the price have to land fast; the shorter the decision, the bolder and simpler the graphics. The display's clock is its time in store (not to be confused with shopper dwell time): a two-week promotion can be corrugated and disposable, while a fixture that stays up for months or years has to survive restocking, cleaning, and handling, which pushes it toward molded, metal, or acrylic. A rough rule of thumb: a short promotion (up to a few months) → corrugated; an ongoing fixture (a season or longer) → molded, metal, or acrylic — and among those three, acrylic for a premium look, metal for weight-bearing shelving, molded plastic for a custom shape at volume. The job is to match both clocks — a bold, simple message on a structure built for how long it actually has to last.
A display's spec usually comes from the retailer's planogram and guidelines — a size envelope, safety rules, sometimes a flammability standard for a particular chain. JCH builds to that brief; it doesn't set the retailer's rules, so the fastest path is to send the retailer's specification along with the product. Designing to it from the start avoids the expensive rework of a display that's rejected at the loading dock. Before volume, a sample is approved against the retailer's spec, and the flat-packed unit gets a transit (ship) test — the standard drop-and-vibration sequence of a shipping test, e.g. an ISTA procedure — so it arrives intact.
The products it holds (dimensions, weight, facings per shelf), the placement (counter, floor, end-cap, shelf), permanent or temporary, your branding and graphics, any retailer specification, and your annual volume. Product weight and the retailer's rules are the key inputs — weight sets the structure and stability, the retailer's guidelines set the size and compliance — and from there the materials, structure, graphics, and flat-pack/assembly are specified together.
Can you build POP and retail displays?
Yes — countertop, floor, PDQ/shelf trays, end-caps, standees, coordinated through a network: molded/thermoformed parts, fabricated acrylic/metal, printed graphics, and assembly. It ships flat where the structure allows, kitted with graphics and instructions. Time in store and the retailer's rules shape the whole job.
What are displays made from?
Corrugated + print (temporary, low-cost), injection-molded (custom bins/hooks/bases at volume), thermoformed (lighter trays/shells), acrylic/PETG (clear premium fronts), metal wire/sheet (weight-bearing shelving/hooks). Most combine several, built to one spec and shipped together where the structure allows.
Permanent or temporary?
Temporary = corrugated/printed, weeks-to-months, low cost, for a promotion. Permanent = molded/metal/acrylic, months-to-years, higher cost, an ongoing fixture. A permanent display only pays off if it stays up long enough to earn back its cost; many brands test temporary first, then go permanent where it performs.
Do you handle graphics and assembly?
Yes — graphics printed/applied, the unit assembled or designed to knock down flat and go together with minimal tools in-aisle, and kitted with parts + graphics + instructions. The goal is a unit a store associate can stand up quickly with minimal tools, because a hard-to-assemble display often doesn't get put out.
What do you need to quote a display?
The products (dimensions, weight, facings), placement (counter/floor/end-cap/shelf), permanent vs temporary, branding/graphics, any retailer spec (size/safety/flammability), and annual volume. Weight sets the structure; the retailer's planogram sets size and compliance.
JCH Design & Manufacturing can coordinate a POP or retail display from parts to graphics to assembly. Send the products, the placement, and the retailer's spec.
Book a 30-minute call