Answers › Plastic & metal products

Can you make both the plastic and metal parts of my product?

Yes — most real products mix materials (a molded plastic housing with a machined shaft, a stamped bracket, fasteners), and that whole bill of materials can be coordinated across the right partners instead of you juggling a molder, a machine shop, and an assembler. JCH coordinates design, tooling, each process, and assembly through a manufacturing network. The hard part is rarely a single piece — it's the interfaces where plastic meets metal.

This is general guidance on combining materials, not a pitch for one shop.

The processes that go into a mixed product

ProcessMakes
Injection moldingPlastic housings, covers, structural and cosmetic parts
CNC machining (mill / turn)Precise metal (or plastic) parts, shafts, brackets, low-volume runs
Sheet-metal stamping / formingBrackets, enclosures, clips, chassis
Die castingComplex metal shapes at volume
FinishingPlating, anodizing, powder coating, decoration
AssemblyBringing the plastic and metal parts together into the finished product

Coordinating these together means the metal and plastic parts are designed to the same interfaces and tolerances, instead of discovering at assembly that two separately-sourced parts don't fit.

How plastic and metal get combined

The right method depends on load, serviceability, and volume — a heat-staked boss is cheap at volume, a threaded insert is better for a repeatedly-opened joint. These are design decisions best made before tooling.

Why the interfaces are the real work

Plastic and metal shrink and move differently — plastic has far higher thermal expansion and its own molded shrinkage, metal is dimensionally stable — so a fit between them has to be engineered, not assumed. The tolerance stack-up across a plastic part, a metal part, and their joint is where mixed-material products usually fail when the pieces are sourced piecemeal: each part is "in spec" on its own drawing, but they don't assemble. Example: a metal shaft pressed into a molded plastic boss. Plastic's thermal expansion (CTE) is roughly an order of magnitude above steel's, so a bore sized for a snug fit at room temperature can loosen when it heats up or shrink onto the shaft when it cools — the clearance has to be set for the whole temperature range (it loosens when hot, grips when cold), not one bench measurement, and the plastic part's own molded shrinkage factored in. Two more that bite: a plastic boss under a pressed or screwed-in metal part can creep (stress-relax) over time and loosen the joint, so you design for the long-term clamp, not day one; and a thin-wall boss can split on a press-fit from hoop stress, so the boss wall and any rib are sized to the insert OD rather than guessed. At a dissimilar-metal interface, watch for galvanic corrosion in the service environment. One coordinator working from a single bill of materials catches that in design, holds one quality standard, and runs the assembly — so the integration risk isn't yours to carry between vendors.

What to provide

Give the full picture: the assembly or bill of materials (or a sample), which parts are plastic and which are metal, how they join, the critical tolerances at the interfaces, cosmetic and finish needs, the volume, and any compliance requirements. A rough CAD assembly or even an annotated sketch of how the pieces fit lets the processes be planned together and the stack-up checked before any tool is cut.

Common questions

Can you make both the plastic and metal parts of my product?
Yes — a molded plastic housing plus machined, stamped, cast, or turned metal and the assembly, coordinated across partners as one bill of materials, so you don't juggle a molder, machine shop, and assembler. JCH coordinates design, tooling, each process, and assembly.

How do plastic and metal parts get combined?
Insert molding (metal placed in the mold), over-molding, threaded inserts heat-set or ultrasonically installed, screws, adhesive, or heat-staking a boss over the part. (Snap-fits are normally plastic-to-plastic, not a metal join.) The method depends on load, serviceability, and volume — heat-staked bosses are cheap at volume; threaded inserts suit repeatedly-opened joints.

What metal processes can be coordinated alongside molding?
CNC machining (milling and turning), sheet-metal stamping/forming, and die casting, plus finishing (plating, anodizing, powder coating). Coordinating them with molding means the metal and plastic parts share the same interfaces and tolerances.

Why use one partner for a mixed-material product?
The interfaces are the hard part. One coordinator works from a single BOM, does DFM across materials, manages the plastic-to-metal tolerance stack-up, and owns one quality standard and the assembly — so you don't carry the integration risk between vendors.

What should I provide for a mixed plastic-and-metal product?
The assembly/BOM (or a sample), which parts are plastic vs metal, how they join, the interface tolerances, cosmetic/finish needs, volume, and any compliance needs. A rough CAD assembly or annotated sketch lets the stack-up be checked before tooling.

JCH Design & Manufacturing can coordinate the whole mixed-material build — molding, machining, stamping, finishing, and assembly — from one bill of materials, and plan the plastic-to-metal interfaces and tolerance stack-up before tooling, so the pieces are far more likely to fit on the first build. Send your assembly, BOM, or a sample; NDA first.

Book a 30-minute call