Answers › Silicone & rubber parts

Can you make silicone or rubber parts?

Yes — seals, gaskets, grips, keypads, tubing and over-molded handles are made by liquid silicone rubber (LSR) injection, solid silicone/rubber compression or transfer molding, or thermoplastic elastomer (TPE/TPR) injection. The right route depends on the properties you need (heat, chemical, food or medical grade), the hardness (durometer), the volume, and whether the soft material is over-molded onto a rigid part.

JCH coordinates design, tooling and production through a manufacturing network, so this is general guidance on specifying a soft part, not a pitch for one shop.

The soft-material options

Material / processBest forNotes
LSR (liquid silicone rubber), injectionPrecision seals, medical/food parts, keypads, tubingTwo-part thermoset cured in a heated tool; fine detail; heat ~-60 to 200°C+; needs a specialized press
Solid silicone / rubber (EPDM, nitrile), compression or transferGaskets, seals, O-rings, bushingsGood for simpler high-durability seals; lower tooling than LSR injection at low volume
TPE / TPR, injectionGrips, soft-touch, over-molds on plasticMolds like plastic on a normal machine; recyclable; lower temp range than silicone

The big divide is thermoset vs. thermoplastic: silicone and rubber cure permanently and can't be re-melted; TPE/TPR melt and re-flow like a plastic. That changes the press, the tool, and whether you can regrind scrap.

Durometer: how soft the part is

Durometer is the hardness, usually on the Shore A scale: roughly 10–20 A for a very soft part (true gels are softer still and are measured on the Shore OO scale), 40–70 A for a typical grip or gasket, and 80–90 A for a firm seal (harder than that moves toward the Shore D scale for rigid materials). Choose it from the job — softer for a comfortable grip or a conforming seal, firmer to hold shape or resist compression set — and state a target durometer with a tolerance, because it drives the material grade and the feel.

Over-molding soft onto rigid

Over-molding a soft material onto a rigid substrate — a grip over a handle, a seal onto a housing — bonds chemically (a compatible material pair, sometimes a primer) and/or mechanically (the soft material locks into undercuts, holes, or grooves). The catch is compatibility: not every soft material bonds to every rigid plastic, so the substrate resin and the over-mold are chosen together, and the rigid part is designed with bond features. Soft materials over-mold onto metal inserts too (a grip over a metal shaft, a seal onto a metal housing), usually with a primer and a mechanical lock since chemical bonding to metal is harder. TPE over-molds easily onto many plastics; LSR-to-plastic or metal needs the right grade and surface prep. (See insert & over-molding.)

Design and process cautions

Grades and compliance

Silicone and TPE come in food-contact (FDA) and medical (USP Class VI, ISO 10993) grades. Those aren't just a material swap — they bring a documentation chain (material certs, biocompatibility data) and often process controls. If the part is food or medical, say so up front, since it changes the grade, the process, and the paperwork. (See food-safe & medical-grade molding.)

Common questions

Can you make silicone or rubber parts?
Yes — seals, gaskets, grips, keypads, tubing, over-molded handles — by LSR injection, solid silicone/rubber compression or transfer molding, or TPE/TPR injection. The route follows the properties, durometer, volume, and whether it's over-molded.

What's the difference between LSR, solid silicone, and TPE?
LSR is a two-part thermoset cured in a heated tool (precise, medical/food grades, heat ~-60 to 200°C+, needs a special press); solid silicone/rubber is compression/transfer molded (seals, gaskets); TPE/TPR molds like plastic, recyclable, over-molds well, but a lower temp range. Thermosets cure permanently; TPE re-melts.

What does durometer mean and which should I pick?
Durometer is hardness, usually Shore A: ~10–20 A very soft (gels: Shore OO), ~40–70 A grips and gaskets, ~80–90 A firm seals (above that, Shore D). Pick from function — soft for grip/conforming seal, firm to hold shape or resist compression set — and give a tolerance.

Can silicone or rubber be over-molded onto a plastic or metal part?
Yes — a grip over a handle, a seal onto a housing. The bond is chemical (compatible pair/primer) and/or mechanical (locks into undercuts). Compatibility matters, so substrate and over-mold are chosen together. TPE bonds to many plastics; LSR-to-plastic needs the right grade and prep.

What should I specify for a silicone or rubber part?
The material family (or the properties you need), the durometer (Shore A) + tolerance, any FDA/USP Class VI/ISO 10993 grade, the color, operating temperature and chemical exposure, and for an over-mold the rigid substrate material so bond compatibility can be confirmed.

JCH Design & Manufacturing can help you choose the material (LSR, silicone, rubber, or TPE), set the durometer and any regulated grade, and design an over-mold that actually bonds. Send a sample, drawing, or the properties you need; NDA first.

Book a 30-minute call