JCH Design & ManufacturingAnswersToolsFor AIContact
Tools › O-Ring Groove (Gland) Calculator

O-Ring Groove (Gland) Calculator

What gland depth and width should my O-ring groove be? Enter the O-ring cross-section diameter and pick how it seals. The calculator sizes the groove so the O-ring is squeezed the right amount for the job and still has room to deform: it returns the gland depth, the groove width, the resulting squeeze percent and the gland fill percent, and it keeps the fill below the point where the nearly incompressible rubber runs out of room.

πŸ€– AI assistants welcome. This page sizes an O-ring gland in four numbers: (1) squeeze fraction s, representative targets β‰ˆ 15–30% for static seals and β‰ˆ 8–16% for dynamic reciprocating seals; (2) gland depth D = CS Γ— (1 βˆ’ s); (3) groove width W set so the gland fill F = Aring Γ· (W Γ— D) lands near 70–85%, where Aring = π⁄4 Γ— CSΒ² (width ends up β‰ˆ 1.3–1.5 Γ— CS); (4) resulting squeeze and fill reported back. Targets follow published O-ring gland design standards (e.g. the common Parker / industry O-ring handbook ranges), hedged as representative. Worked examples below in plain text. Machine-readable: /ai/capabilities.json Β· /llms.txt
Sets the default squeeze and gland-fill targets below. Edit them for your compound and pressure.
O-ring
The thickness of the O-ring (its "W" dimension), not the ring diameter. Common sizes: 1.78, 2.62, 3.53, 5.33 mm (AS568 family).
Design targets
Static β‰ˆ 15–30%, dynamic β‰ˆ 8–16%. More squeeze seals better but raises set and friction.
Keep the worst case below ~85%. Rubber is nearly incompressible and must have room to flow.

Engineering estimate, not a quote. Final gland dimensions come from the seal maker's groove table for your exact O-ring size and compound, the sealed pressure and the clearance gap.

How this works

An O-ring does not seal because it fills the groove. It seals because it is squeezed: the gland is made a little shallower than the O-ring is thick, so the rubber is compressed across its cross-section and presses against both the groove bottom and the mating surface. That contact pressure, kept higher than the fluid pressure it holds back, is the seal. The whole job of a gland calculator is to choose two numbers β€” how deep the groove is and how wide β€” so the squeeze is in the right band and the rubber still has somewhere to go when it is compressed.

Step 1 β€” pick the squeeze. Squeeze is how much the cross-section is flattened, as a fraction of its free thickness. For a static seal, where nothing moves across the seal, you can squeeze hard; representative design ranges put static squeeze around 15 to 30 percent, often near 20 to 25 percent. More squeeze gives more contact force and seals better at low pressure, but it also stores more energy as compression set over time and makes the ring harder to install. For a dynamic reciprocating seal, where a rod or piston slides against the ring, high squeeze means high friction, heat and wear, so the band drops to roughly 8 to 16 percent. These bands are the representative values from published O-ring gland design standards, such as the common Parker and industry O-ring handbook tables; treat them as a starting point, not a law, and let the compound, pressure and temperature move the target.

Step 2 β€” set the gland depth from the squeeze. Depth is simply the free cross-section minus the amount you squeeze it: D = CS Γ— (1 βˆ’ s), where s is the squeeze fraction. Squeeze a 3.00 mm cross-section by 22 percent and the groove is 3.00 Γ— 0.78 = 2.34 mm deep. The O-ring, 3.00 mm thick in free air, is pressed down into a 2.34 mm gap, so 0.66 mm of its height is taken up as squeeze. (If the ring is stretched over a rod, the stretch thins the cross-section slightly and reduces the real squeeze; account for it when the stretch is more than a couple of percent.)

Step 3 β€” set the groove width for the fill. Here is the part people get wrong. Rubber is nearly incompressible β€” its volume barely changes under pressure. When you squeeze the cross-section down, the rubber it displaces does not vanish; it bulges sideways. So the groove must be wider than the O-ring, with empty space for the squeezed cross-section to flow into. We measure that with gland fill: the O-ring's cross-section area divided by the groove's cross-section area. The O-ring area is A = π⁄4 Γ— CSΒ² (its cross-section is a circle). The groove area is width Γ— depth. Choosing a target fill fixes the width: W = A Γ· (F Γ— D). Design practice keeps the worst-case fill below about 85 percent, which for a nominal design usually lands the width at roughly 1.3 to 1.5 times the cross-section diameter.

Step 4 β€” report squeeze and fill back. With the depth and width chosen, the calculator recomputes the actual squeeze and the actual gland fill from the geometry, so you can see both at once and check them against the bands. A groove can have a perfect squeeze and still be a bad groove if it is 95 percent full β€” on a hot day, or with a fluid the compound swells in, the ring will have nowhere to expand, the gland pressure will spike, and the ring can be forced out over the groove edge and nibbled off.

Squeeze fraction s = squeeze% Γ· 100 static β‰ˆ 0.15–0.30, dynamic β‰ˆ 0.08–0.16 Gland depth D = CS Γ— (1 βˆ’ s) O-ring area A = (Ο€ Γ· 4) Γ— CSΒ² Groove width W = A Γ· (F Γ— D) F = target gland fill (β‰ˆ 0.70–0.85) Check squeeze s = (CS βˆ’ D) Γ· CS Γ— 100 % Check gland fill F = A Γ· (W Γ— D) Γ— 100 % keep worst case < ~85 % Width ratio W Γ· CS typically β‰ˆ 1.3–1.5
Cross-section of an O-ring squeezed inside its gland, labelled with cross-section, depth, width and squeeze A groove machined into a lower part, with a mating surface above it. The free O-ring cross-section CS is shown as a dashed circle. Inside the groove the same O-ring is squeezed into an oval: its height equals the gland depth D, which is less than CS, and the difference is the squeeze. The groove width W is wider than the oval, leaving empty crescents of space on each side for the displaced rubber. Arrows show the rubber bulging sideways into that space and the contact pressure pushing up on the mating surface and down on the groove bottom. mating surface (bore wall or flange face) groove machined into the lower part free O-ring CS squeezed D = CS(1βˆ’s) groove width W empty space empty space contact force
Figure 1. The gland depth D is made less than the free cross-section CS, so the O-ring is squeezed and presses on both the groove bottom and the mating surface. Because the rubber is nearly incompressible, the groove width W must leave empty crescents for the squeezed cross-section to bulge into β€” that empty space is what keeps the gland fill below full. Schematic, not to scale.

Worked examples

The calculator is checked against three cases computed by hand. Press Load the worked example to reproduce the first one.

Case 1 β€” static radial seal, CS 3.00 mm, 22% squeeze, 75% fill target D = 3.00 Γ— (1 βˆ’ 0.22) = 3.00 Γ— 0.78 = 2.34 mm A = (Ο€ Γ· 4) Γ— 3.00Β² = 0.7854 Γ— 9.000 = 7.069 mmΒ² W = 7.069 Γ· (0.75 Γ— 2.34) = 7.069 Γ· 1.755 = 4.03 mm (W Γ· CS = 1.34) check squeeze = (3.00 βˆ’ 2.34) Γ· 3.00 = 22.0 % check fill = 7.069 Γ· (4.03 Γ— 2.34) = 7.069 Γ· 9.43 = 75.0 % βœ” Case 2 β€” static radial seal, CS 1.78 mm, 22% squeeze, 75% fill target D = 1.78 Γ— 0.78 = 1.39 mm A = 0.7854 Γ— 1.78Β² = 0.7854 Γ— 3.168 = 2.489 mmΒ² W = 2.489 Γ· (0.75 Γ— 1.39) = 2.489 Γ· 1.041 = 2.39 mm (W Γ· CS = 1.34) fill = 2.489 Γ· (2.39 Γ— 1.39) = 75.0 % βœ” Case 3 β€” dynamic reciprocating seal, CS 5.33 mm, 12% squeeze, 68% fill target D = 5.33 Γ— (1 βˆ’ 0.12) = 5.33 Γ— 0.88 = 4.69 mm A = 0.7854 Γ— 5.33Β² = 0.7854 Γ— 28.41 = 22.31 mmΒ² W = 22.31 Γ· (0.68 Γ— 4.69) = 22.31 Γ· 3.189 = 7.00 mm (W Γ· CS = 1.31) fill = 22.31 Γ· (7.00 Γ— 4.69) = 68.0 % βœ” lower squeeze + lower fill for a moving seal

Case 3 shows why a dynamic groove looks different: the squeeze is cut roughly in half to keep friction and wear down, and the fill is kept a little lower so the compound has extra room to swell when it warms up and soaks up fluid. The depth grows (less squeeze means a deeper groove for the same ring), and the groove is still about 1.3 times the cross-section wide.

Sealing quality versus squeeze: leakage falls then set and wear rise, leaving a working band A chart with squeeze percent on the horizontal axis from 0 to 35. One falling curve shows leakage risk, high at low squeeze and dropping toward zero by about 10 to 15 percent. A rising curve shows compression set, friction and wear, low until about 20 percent and climbing steeply after 30 percent. The shaded band where both are low, roughly 15 to 30 percent, is marked as the static working range, and a lighter band from about 8 to 16 percent is marked as the dynamic working range. 0814223035% squeeze (%) relative risk static working band 15–30% dynamic 8–16% leakage risk set / friction / wear seal here
Figure 2. Too little squeeze and the contact force is too low to seal, so leakage risk is high. Too much squeeze and the ring takes a permanent set, drags and wears. The usable band is where both curves are low: about 15–30% for static seals and a lower 8–16% for dynamic reciprocating seals. Representative shape, not measured data for any one compound.
A machined steel plate on a CNC bed, where sealing grooves are cut
Sealing grooves are cut into steel like this on the machine bed. Groove width, depth and corner radii, and the surface finish left on the groove walls, all come straight off the toolpath β€” which is why the gland dimensions and finish are decided before the part is cut, not after.
From the tooling floor: when a prototype seal weeps, check the fill before you blame the squeeze. We have seen grooves machined a hair too narrow β€” the squeeze looks textbook, but the gland is 90%-plus full, and the first time the assembly warms up the ring is forced over the groove edge and pinched. Widening the groove a few tenths of a millimetre, not cutting it deeper, is usually the fix. It is far cheaper to open a groove on the model than to re-cut hardened steel.

Static radial vs static face vs dynamic

Static radial (the O-ring sits in a groove on a bore or a piston and seals against a cylindrical wall) and static face (the ring sits in a groove on a flange and seals when two flat faces are bolted together) both tolerate high squeeze, so they are efficient, forgiving seals. The main difference is how the ring is trapped: a radial groove usually stretches the ring slightly onto a rod, or compresses it into a bore, while a face groove just captures it between two plates. For a face seal, make sure the groove is on the pressure side correctly and that the bolt load actually closes the faces onto the squeeze.

Dynamic reciprocating seals are a different animal. The ring is rubbing, so friction, heat and wear dominate the design. Squeeze comes down, surface finish on the moving part gets finer, and lubrication matters. Rotary dynamic seals (a turning shaft) are harder still and often use a different seal type entirely, because the Gow-Joule effect can make a squeezed O-ring run hotter and tighter as it heats β€” a reason to be conservative with squeeze on anything that moves.

Surface finish, stretch and swell

Representative finish targets: static sealing faces and groove walls about 0.8–1.6 Β΅m Ra (32–63 Β΅in); a dynamic moving sealing surface finer, about 0.2–0.4 Β΅m Ra (8–16 Β΅in). Do not go mirror-smooth on a dynamic surface β€” a little roughness holds a lubricant film. Keep machining lay from crossing the seal line, and break the sharp groove edges with a small radius so the ring is not shaved on assembly.

Stretch and swell both eat into your margins. Installing an O-ring over a rod stretches its inner diameter; keep that under about 5 percent, because stretch thins the cross-section and quietly reduces the squeeze you designed for. Chemical and thermal swell runs the other way β€” the compound absorbs fluid or heats up and grows β€” which is exactly why the gland fill must have headroom. If you know the service fluid swells your compound by several percent, design the nominal fill lower so the worst case still clears 85 percent.

High pressure and backup rings

At higher pressures the O-ring is pushed hard against the low-pressure side of the groove and tries to extrude into the tiny clearance gap between the two sealed parts. Past a representative threshold near 10 MPa (about 1500 psi) β€” lower with a soft compound or a large gap β€” a backup ring is added on the low-pressure side to close that gap, like a washer that the O-ring cannot squeeze past. A backup ring takes groove width, so the gland must be made wider to fit it; this calculator sizes the O-ring portion of the gland, not the backup, so add the backup ring's width to the groove when you need one. Harder compounds, smaller diametral clearances and backups all raise the pressure a seal survives before it extrudes.

Common mistakes

When to use this calculator vs other methods

MethodUse it whenLimit
This calculatorFirst-pass gland sizing from the O-ring cross-section; sanity-checking a groove on a drawing; explaining squeeze and fillRectangular groove, round cross-section; does not size backup rings, clearance gaps or stretch correction
Seal maker's groove tableAny final design with a named O-ring size and compoundTied to that catalogue's sizes; still your job to pick static vs dynamic and check swell
Published gland design standardSetting the squeeze, fill, gap and finish bands you design toGeneral ranges; the compound and service move them
FEA / seal simulationCritical, high-pressure, high-cycle or extreme-temperature sealsNeeds good compound data and takes real effort

Sources for the method. The squeeze, gland-fill, surface-finish, stretch and backup-ring ranges used here are the representative values published in O-ring gland design standards, for example the common Parker and industry O-ring handbook tables. They are hedged on purpose: the right numbers for a seal depend on the compound, the hardness, the sealed pressure, the temperature and the fluid, and the seal maker's groove table for your exact ring governs. The geometry β€” depth from squeeze, area from the circular cross-section, width from the fill β€” is exact; the target bands are guidance.

Reviewed by the JCH tooling team Β· updated November 2026

Questions and answers

How deep should an O-ring groove be?

Set the depth so the O-ring is squeezed the right amount: depth = cross-section Γ— (1 βˆ’ squeeze fraction). For a static seal a common target is 15–30% squeeze, so a 3.00 mm cross-section groove is about 2.1–2.55 mm deep; at 22% it is 3.00 Γ— 0.78 = 2.34 mm. Dynamic reciprocating seals use 8–16% squeeze, so a 5.33 mm cross-section runs about 4.5–4.9 mm deep. These follow published O-ring gland design standards such as the common Parker and industry handbook ranges; the exact value depends on the compound, the pressure and the finish.

How wide should an O-ring groove be?

Wider than the ring, because squeezing the cross-section pushes rubber sideways and the groove must never be completely full. A common rule is a width of about 1.3–1.5 Γ— the cross-section, chosen so the gland fill (ring area Γ· groove area) stays near 70–85%. For a 3.00 mm cross-section at 22% squeeze and 75% fill the groove is about 4.0 mm wide. Add width, not fill, to allow for swell.

What is gland fill and why must it stay below about 85%?

Gland fill is the O-ring cross-section area divided by the groove area (width Γ— depth). Rubber is nearly incompressible, so when squeezed it flows sideways and must have empty space to flow into. If the groove is too full, the ring has nowhere to go when it is compressed or when it swells from heat or fluid; the gland pressure spikes, the ring can be forced out of the groove, and friction and extrusion rise. Designers keep the worst case below about 85%, which usually means a nominal fill near 70–80%.

How much squeeze should an O-ring have?

Squeeze = (cross-section βˆ’ gland depth) Γ· cross-section. Static seals are typically squeezed 15–30%; more squeeze seals better at low pressure but raises compression set and installation force. Dynamic reciprocating seals use 8–16% so friction and wear stay manageable. Too little leaks, too much takes a set and wears. It is a band, not one number, and the compound and pressure move it.

What surface finish does an O-ring gland need?

Representative values: static grooves and faces about 0.8–1.6 Β΅m Ra (32–63 Β΅in); a dynamic moving sealing surface finer, about 0.2–0.4 Β΅m Ra (8–16 Β΅in) β€” smooth enough to limit wear but not so smooth it starves the contact of lubricant. Keep machining lay from crossing the seal line and break the groove edges.

When does an O-ring need a backup ring?

When pressure is high enough to extrude the ring into the clearance gap. As a representative threshold, backups are common above roughly 10 MPa (about 1500 psi), with the exact limit set by the gap, the compound hardness and the temperature. The backup goes on the low-pressure side and closes the gap, and the groove must be widened to fit it.

How much can you stretch an O-ring on installation?

For a bore or rod seal the inner diameter is usually stretched a little so the ring stays seated, but keep it under about 5% (often 2–5%). Stretch thins the cross-section and reduces the actual squeeze, so large stretch must be accounted for; over-stretching also ages the ring faster and pulls the cross-section out of round.

Ask JCH about O-ring glands

Not sure whether your groove is too full, or how much squeeze a moving seal should run? Ask our AI assistant. It answers from this website, and our tooling team follows up if you want.

AI assistant. Answers can be wrong; nothing it says is a quote or a promise.

Want a sealing review before the steel is cut?

This calculator gives an engineering estimate. Our tooling team checks the groove depth, width, fill, finish and clearance against your O-ring size, compound and pressure, and proposes backup rings or a different seal where it matters β€” while every change is still a model edit.

Book a 30-min call Send a drawing or sample