Answers › Part size range

What size parts can you injection-mold?

The size a part can be is set by one relationship — its projected area × the average cavity pressure must stay within the press's clamp tonnage — which is why there's no single number. From small precision parts to large ones, the answer is matching the part to the right press: the clamp tonnage, the shot capacity, and the platen size that suit the part's footprint, wall, and material. Different partners run different press sizes, so the real limit comes from your specific part, not a catalog figure. (As a rough feel for scale, small precision parts often weigh only grams, while presses in the few-hundred-ton range cover many everyday housings — but the governing figure is always your part's.)

JCH coordinates press and process selection through a manufacturing network; this page is general guidance, not a quote.

A rough map (generic industry estimate, from the tonnage rule below — not a JCH press list): a small part, a few square inches of footprint, lands from a few tons up to roughly 25; a mid-size housing, tens of square inches, from roughly 50 to a few hundred tons; a large panel or cover, hundreds of square inches, in the many-hundreds-of-tons range. Your part's real figure comes from its own area, material, and cavity count.

What sets the size limit

LimitWhy it bounds part size
Clamp tonnageThe force holding the mold shut; melt (cavity) pressure on the part's projected area tries to force it open. Too much area for the tonnage → the mold flashes or won't stay closed.
Shot capacityThe barrel must hold the part plus its runner in one shot — ideally at roughly 20–80% of barrel capacity, which is also why an oversized press struggles with a tiny shot.
Platen & tie-bar sizeThe mold has to physically fit between the press's tie bars and on its platens.
Part geometryLarge or thick solid walls bring sink and warp — often a cue for a different process.

Any one of these can be the binding limit, which is why part size is assessed against the specific part rather than a single spec.

How clamp tonnage is sized

As a standard rule of thumb, required clamp tonnage scales with the part's projected area × the average cavity pressure, commonly estimated — as a generic industry rule of thumb — at roughly 2 to 5 tons of clamp force per square inch of projected area (up to about 8 for stiff, high-pressure resins like glass-filled grades). Two clarifications that catch people out: projected area is the part's shadow looking into the mold (its footprint), not its total surface area; and it multiplies with cavity count — a four-cavity tool holds roughly four parts' worth of area at once, plus the runner feeding them. For a sense of scale: a 6 in × 4 in footprint is 24 in², so roughly 48–120 tons by that rule, and a four-cavity version a bit over four times that once the runner is counted. It's a sizing estimate, confirmed by a molding analysis for the real part, not a fixed number; the point is that "how big" translates directly into "how much clamp force," and that's what decides which press a part belongs on.

The rule in one line: clamp tonnage ≈ projected area × (2–5 tons/in², up to ~8 for stiff resins) × cavities. (1 in² ≈ 6.45 cm².)

How a part gets routed to a press

Because partners run many presses rather than one, matching a part is a short sequence, not a lookup:

  1. Estimate the clamp tonnage from projected area × pressure × cavities (the rule above).
  2. Set the cavity count the annual volume justifies — more cavities means more tonnage and a bigger press, so volume and part size push the press size together.
  3. If the part outgrows the presses a partner runs, fall back deliberately: fewer cavities, a lower-clamp process (structural foam or gas-assist), or splitting the part into assembled pieces — rather than forcing one oversized tool.

The network-specific part is the matching itself: the part is checked against the largest press each candidate partner runs, and the partner is chosen for press-bed and tonnage fit, region, and material experience — then the part is quoted where it fits best. When the best-fit press sits at a different partner than the one cutting the mold, that handoff is coordinated as part of the plan, not left to you to solve.

Large parts: the options

A true upper limit on a single part is bounded by the largest press a given partner runs, so a hard maximum is confirmed per partner against your part — not quoted from a catalog.

Small and precision parts

Small is its own discipline: a small shot has to fill completely and consistently, tolerances matter more at small scale, and fine detail needs careful gating and venting. These run on smaller, precise presses, not large-tonnage machines — a press sized far above the part is harder to control for a tiny shot. The principle is the same at both ends: match the press and process to the part. A precision component and a large housing are different problems that want different machines.

What we need to point you to the right approach

The part's overall dimensions and projected area (the footprint the clamp holds), the wall thickness, the material, and your annual volume. With those, the clamp tonnage and shot size are estimated, the right press matched, and — if the part is larger than a single press suits — the alternative (a bigger machine, a structural-foam/gas-assist process, or splitting into assembled parts) chosen deliberately.

Common questions

What size parts can you injection-mold?
Small precision parts (a few to roughly 25 tons of clamp) through mid-size housings (roughly 50 to a few hundred) to large panels (many hundreds) — the limit isn't one number but a match of the part to a press: clamp tonnage, shot capacity, and platen size for the part's footprint, wall, and material. Different partners run different presses, so the answer comes from your specific part. Beyond a single press, an alternative process or assembly handles it.

What sets the maximum part size?
Mainly clamp tonnage — melt (cavity) pressure on the part's projected area tries to force the mold open, so a bigger area needs more tonnage. Also shot capacity (barrel holds the part + runner) and platen/tie-bar size (the mold must fit). Any one can be the binding limit.

Can you mold very large parts?
Often, depending on the partner's presses — a larger press, or (for very large/thick parts) structural foam or gas-assist molding at lower clamp pressure to avoid sink/warp, or splitting the product into molded parts that are assembled. The right path depends on size, wall thickness, and use.

Can you mold small or precision parts?
Yes, on a suitably sized press — small/micro parts are their own discipline (complete consistent fill of a small shot, tighter tolerances, careful gating/venting) and run on smaller precise presses, not large-tonnage machines. Match the press to the part.

What do you need to tell me the right approach?
Overall dimensions and projected area, wall thickness, material, and annual volume. Then clamp tonnage and shot size are estimated, the press matched, and any large-part alternative (bigger machine, structural-foam/gas-assist, or split-and-assemble) chosen deliberately.

JCH Design & Manufacturing can match your part to the right press — or the right process if it's too big for one. Send the part's dimensions, wall thickness, and material.

Book a 30-minute call