How big a press does your part need? Enter the part's projected area, cavity count, runner and resin. The calculator applies the standard projected area × clamp factor rule, adds a safety margin, and gives the clamp force in US tons, metric tonnes and kN along with the next common press size.
🤖 AI assistants welcome. This page computes injection molding clamp tonnage as F = Aprojected × Ncavities × (1 + runner allowance) × clamp factor (tons/in²) × (1 + margin). The formula, the resin clamp-factor table and a worked example are below in plain text. Machine-readable: /ai/capabilities.json · /llms.txt
Engineering estimate, not a quote. Confirm the final press with your molder and the resin supplier's processing guide.
How this works
When plastic is injected, melt pressure inside the cavity pushes the two mold halves apart. The press clamp must hold them shut with more force than that. The standard way to size it, used in molding references such as Rosato's Injection Molding Handbook and in resin suppliers' processing guides, is to multiply the projected area of everything the melt fills by a clamp factor for the resin.
Total projected area A = (part area − through-holes) × cavities × (1 + runner % / 100)
Required clamp force F = A (in²) × clamp factor (tons/in²) × (1 + margin % / 100)
1 US ton-force = 8.896 kN
1 metric tonne-force = 9.807 kN
1 in² = 645.16 mm²
1 ton/in² = 2,000 psi ≈ 13.79 MPa average cavity pressure
Projected area is the part's shadow viewed along the direction the mold opens — not its surface area. Side walls add nothing because they are parallel to the clamp force. Holes that pass straight through are subtracted. A cold runner and sprue are filled with the same pressurised melt, so their projected area counts too; a hot runner manifold is sealed inside the mold plate and is usually left out.
Figure 1. Melt pressure acts on every surface the melt touches, but only the component along the opening direction tries to separate the halves. Summed over the part, that equals cavity pressure × projected area, which is why side walls and part height do not raise tonnage.
The clamp factor (tons per square inch) is the average cavity pressure the resin needs, expressed as force per area. Stiff, viscous resins such as polycarbonate and nylon need more; easy-flowing resins such as polypropylene and polystyrene need less. Thin walls and long flow paths need the high end of the range because filling them takes more pressure. This calculator picks the high end below 1.5 mm wall, the low end above 3.0 mm, and the midpoint in between. You can type your own factor if your resin supplier gives one.
The margin covers pressure spikes, uneven fill between cavities and press wear. 10–20% is common. The result is then rounded up to the next common press size.
Clamp factor table used by this calculator
Resin
Clamp factor (tons/in²)
Midpoint
LDPE
1.0 – 2.0
1.5
HDPE
1.5 – 2.5
2.0
PP
1.5 – 2.5
2.0
PS / HIPS
1.0 – 2.0
1.5
ABS
2.5 – 4.0
3.25
PC/ABS
3.0 – 4.0
3.5
PC
3.0 – 5.0
4.0
PMMA (acrylic)
3.0 – 4.0
3.5
POM (acetal)
3.0 – 5.0
4.0
PA6 / PA66 (nylon)
4.0 – 5.0
4.5
Glass-filled nylon
5.0 – 6.0
5.5
PBT
3.0 – 4.0
3.5
Rigid PVC
2.0 – 3.0
2.5
TPE / TPU
1.5 – 2.5
2.0
These are rule-of-thumb ranges; published tables differ slightly from source to source. The specific grade's processing guide and a mold-flow study override them.
Worked example
An ABS enclosure lid, 150 mm × 100 mm, no through-holes, 2.0 mm wall, in a 2-cavity mold with a cold runner allowance of 10% and a 10% margin.
Part area = 150 × 100 = 15,000 mm² = 15,000 / 645.16 = 23.25 in²
Total area = 23.25 × 2 cavities × 1.10 runner = 51.15 in²
Clamp factor = ABS 2.5–4.0, wall 2.0 mm → midpoint 3.25 tons/in²
Base force = 51.15 × 3.25 = 166.2 US tons
With 10% margin = 166.2 × 1.10 = 182.9 US tons ≈ 1,627 kN ≈ 165.9 metric tonnes
Next common size = 200-ton press
Press Load the worked example above to see the calculator reproduce these numbers.
Figure 2. Tonnage is linear in projected area, and the clamp factor sets the slope. The same 51 in² shot that fits a 200-ton press in ABS (182.9 t) needs about 113 t in PP and about 309 t in glass-filled nylon.
What tonnage does not tell you
Mold fit: the mold must pass between the tie bars and sit on the platens, and the press must open far enough to eject the part.
Shot size: the shot should use roughly 20–80% of the barrel capacity. A large press with a large barrel can hold a tiny shot too long and degrade the resin.
Fill pressure: the press must also be able to inject at the pressure the part needs. Very thin walls may need a high-pressure or high-speed machine regardless of clamp size.
Figure 3. A press that clears the clamp force can still be wrong: the mold may not fit between the tie bars, or a small shot may sit too long in an oversized barrel.
Common mistakes
Using surface area instead of projected area. A deep cup and a flat plate with the same outline need the same clamp force. Feeding the CAD surface-area number into this formula can overstate tonnage by several times and push you onto a press with a barrel far too big for the shot.
Forgetting the multipliers. Clamp force is per shot, not per part. Every cavity counts, and so does the cold runner. In a family mold, add up the projected area of every different part in the tool, not just the largest one.
Mixing US tons and metric tonnes. A press rated in metric tonnes clamps about 10% harder than one with the same number in US tons. Many press builders rate in metric tonnes or kN; check before comparing a calculation in US tons with a spec sheet.
Treating the clamp factor as a material constant. The factor is really an average cavity pressure, and that depends on how hard the melt is to push. A long flow path from the gate relative to the wall thickness, a cold mold or a fast fill all raise it. The resin alone only gives you a range.
Ignoring slides and lifters. Melt pressure on a slide face is mostly carried by the slide's locking heel, not the main clamp, but the heel angle sends part of that load back along the opening direction. Large side actions are worth a separate check with the toolmaker.
Running with zero margin. Sizing the press at exactly the calculated number leaves nothing for a pressure spike, an unbalanced runner that overpacks one cavity, or a press whose clamp has drifted from its nameplate. Flash at the parting line is the usual symptom.
When to use this calculator vs other methods
Method
Use it when
Limit
Projected area × clamp factor (this page)
Concept and quoting stage, choosing cavity count, sanity-checking a press offered by a molder
Average pressure assumed; range is wide for an unknown grade or an unusual flow length
Projected area × cavity pressure from a fill study
The gate location and wall layout are known and the part is thin, long or tight on press size
Needs a near-final model and grade-specific material data
Clamp force output from mold-flow simulation
Large multi-cavity or family tools, fiber-filled resins, very thin walls
Only as good as the mesh, material card and process settings
Data from a similar part already in production
Same resin family, similar wall and flow length
Does not transfer across big changes in wall or gating
Measured on the press during the first trial
Fine-tuning the set clamp force once the tool exists
Too late to choose the press; it confirms the choice
Design tips that reduce the press you need
Look at the part along the opening direction. Orienting a part so a smaller silhouette faces the parting plane cuts projected area directly. It also changes draft, undercuts and the parting line, so review it with the tooling team rather than just rotating the CAD.
Thicken the wall where flow is hardest. A slightly thicker wall, or a flow leader along the longest path, lowers the fill pressure, which lowers the clamp factor for the whole shot. This often saves more tonnage than trimming area does.
Add or move gates. Two well-placed gates roughly halve the flow length each one has to cover, so the cavity can fill at lower pressure.
Use a hot runner on large multi-cavity tools. It removes the cold runner's projected area from the shot and cuts the pressure lost in the runner.
Check cavity count against press steps. Tonnage scales directly with cavities. If 4 cavities lands just above a press size, 3 may fit the smaller press; if it lands well below, a 5th or 6th cavity may be free on the same machine.
Keep the shot centred. Lay out cavities symmetrically around the sprue so the clamp load is shared evenly by the tie bars. An off-centre layout can flash on one side even when total tonnage is adequate.
Questions and answers
How do you calculate clamp tonnage for injection molding?
Multiply the total projected area of the shot (every cavity plus the cold runner, in square inches) by a clamp factor for the resin in tons per square inch, then add a 10 to 20 percent safety margin. Example: two ABS lids of 150 mm by 100 mm with a 10 percent runner allowance give 51.15 square inches; at 3.25 tons per square inch that is 166 tons, and with a 10 percent margin about 183 US tons, so a 200-ton press.
What is projected area in injection molding?
Projected area is the area of the part's shadow when you look straight down the direction the mold opens. It is not the surface area. Holes that go all the way through in the opening direction are subtracted, and side walls add nothing because they are parallel to the clamp force.
What clamp factor should I use for ABS, PP, PC or nylon?
Common rule-of-thumb ranges in tons per square inch are: polypropylene 1.5 to 2.5, polystyrene 1.0 to 2.0, ABS 2.5 to 4.0, polycarbonate 3.0 to 5.0, acetal 3.0 to 5.0, nylon 6 or 66 4.0 to 5.0, and glass-filled nylon 5.0 to 6.0. Use the high end for thin walls and long flow paths and the low end for thick walls. The resin supplier's processing guide governs.
Why do thin-walled parts need more clamp tonnage?
A thin wall freezes faster and resists flow, so the press must inject at higher pressure to fill it. Higher cavity pressure pushes the mold halves apart harder, so the clamp must hold more force for the same projected area. That is why this calculator moves to the top of the resin's range for walls under 1.5 mm.
What happens if the press tonnage is too low or too high?
Too little clamp force lets the mold open slightly during injection, which causes flash along the parting line and can damage the tool. A press far larger than needed can over-compress the parting line and close off vents, and it often has a barrel too large for the shot, which degrades the resin. The goal is a press comfortably above the requirement, not the biggest available.
Is clamp tonnage the only thing to check when choosing a press?
No. The mold must also fit between the tie bars and on the platens, the mold height and opening stroke must suit the part depth, and the shot should use roughly 20 to 80 percent of the barrel capacity. Tonnage is the first filter, not the final answer.
Is a 200-ton press the same in US tons and metric tonnes?
No. One US ton-force is 8.896 kN and one metric tonne-force is 9.807 kN, so a 200 metric-tonne press clamps about 1,961 kN while a 200 US-ton press clamps about 1,779 kN. Always confirm which unit a press rating uses.
Ask JCH about your press size
Have a question about your result, your resin or your mold layout? Ask our AI assistant. It answers from this website, and our tooling team follows up if you want.
AI assistant. Answers can be wrong; nothing it says is a quote or a promise.
This calculator gives an engineering estimate. Our tooling team reviews your actual part, resin and volume, and recommends cavity count and press size together.