Answers › Powder coating & metal finishing

Does JCH offer powder coating and metal finishing?

Yes — JCH coordinates powder coating and other metal finishes through a manufacturing network, on the metal parts in a product. Powder coating applies a dry powder electrostatically, then bakes it into a tough, even, solvent-free film — more durable than wet paint. One honest limit up front: it's for metal, because the oven bake would melt most molded plastics.

JCH coordinates the finish through the network; this page is general guidance, not a quote.

Why powder coat

Wet paint still wins for a few cases — parts too large for an oven, heat-sensitive assemblies, or certain specialty finishes — so the finish is matched to the part, not assumed.

The process (and the step people underrate)

  1. Clean & pretreat — degrease, then a conversion coat (phosphate or similar).
  2. Apply — charged powder sprayed onto the grounded part, so it wraps and clings.
  3. Bake — the oven melts and cures the powder into a continuous film.
  4. Inspect — film thickness, coverage, adhesion, color.

Pretreatment is the hidden half. Most of the adhesion and corrosion resistance comes from that first cleaning-and-conversion step, not the colored powder on top. A beautifully coated part with poor pretreatment peels and rusts underneath early, especially outdoors — so for a corrosive or outdoor part, a better pretreatment or a primer is added. Powder coating is a system: pretreat, powder, cure.

Which powder (outdoor vs indoor)

PowderBest for
PolyesterOutdoor — resists UV far better than epoxy (the standard exterior choice; super-durable grades for the longest life)
EpoxyIndoor — excellent chemical/corrosion resistance and a tough film, but chalks and fades in sun
Epoxy-polyester hybridIndoor — decorative and durable, a common general choice
Super-durable polyester (or FEVE fluoropolymer where offered)Architectural — long outdoor life

Rule of thumb: outdoors or UV → polyester; indoors with chemical or corrosion demands → epoxy can be the better film. Confirm against the part's real environment — the wrong choice chalks or corrodes early.

What usually goes wrong

Other metal finishes we coordinate

Powder coating is one option; the network also coordinates anodizing (aluminum), plating (zinc, nickel, chrome), e-coat, passivation (stainless), and wet paint — each matched to the metal and the environment. For a part that's both plastic and metal, see plastic + metal parts; for finishes molded into a plastic surface, see surface texture & finish.

What we need to quote one

The part and its metal, the environment (indoor, outdoor, UV, salt, chemical), the color/gloss/texture (a RAL number or sample), any spec it must meet (a salt-spray hour target, a film-thickness range), and your annual volume. The environment is the key input — it decides the pretreatment and powder as much as the color does. If the part is plastic rather than metal, we'll say so and point to molded-in color or another decoration.

Common questions

Do you offer powder coating and metal finishing?
Yes — coordinated through a network, on metal parts: brackets, housings, frames, hardware. Powder is applied electrostatically and baked into a tough, solvent-free film. Honest limit: it's for metal — the bake melts most plastics, which get molded-in color or another decoration instead.

Why powder coat instead of wet paint?
A thicker, tougher film (better chip/scratch/corrosion resistance), even coverage on edges without runs/drips, a wide color-gloss-texture range, no solvents (overspray reclaimable), and cost-effective at volume. Wet paint still wins for oversize parts, heat-sensitive assemblies, or some specialty finishes.

How does it work, and why does pretreatment matter?
Clean + pretreat (degrease + conversion coat), apply powder electrostatically, bake to cure, inspect. Most adhesion and corrosion resistance come from the pretreatment, not the color — poor pretreat and the finish peels/rusts early. Powder coating is a system: pretreat, powder, cure.

Which powder — outdoor or indoor?
Polyester for outdoors (resists UV far better than epoxy); epoxy for indoors (great chemical/corrosion resistance but chalks in sun); epoxy-polyester hybrid for indoor decorative/durable; super-durable polyester (or FEVE fluoropolymer where offered) for architectural outdoor life. Confirm against the real environment.

What do you need to quote a finish?
The part and metal, the environment (indoor/outdoor/UV/salt/chemical), color/gloss/texture (RAL or sample), any spec (salt-spray hours, film thickness), and annual volume. Environment drives the pretreatment and powder choice. If it's plastic, we'll point to molded-in color instead.

JCH Design & Manufacturing can coordinate powder coating or another metal finish for your part. Send the part, the metal, and where it's used.

Book a 30-minute call