Yes — JCH coordinates molded, metal, and assembled parts for marine use through a manufacturing network. What makes a part a marine part isn't its shape but surviving the environment — sustained UV, salt water and spray, moisture, temperature swings, and impact — so material and finish choice drive the whole design. The wrong resin or hardware can chalk, crack, or corrode within a season or two.
JCH coordinates the molding, metal parts, and assembly through the network; this page is general guidance, not a quote.
| Material | Marine use |
|---|---|
| ASA | The most UV-stable of the common styrenics — behaves like ABS but made to weather; exterior trim, housings, vents |
| HDPE / UHMW | Tough, water/chemical-resistant, non-marking; boards, rub rails, wear parts (UV-stabilized grade for sustained sun) |
| Polypropylene | Good moisture/chemical resistance; storage and non-structural parts (needs a UV-stabilized grade; embrittles in cold) |
| Polycarbonate (UV-stabilized + hard-coat) | Clear windows, lenses, covers — can craze with fuel, solvents, or sunscreen, so check chemical exposure |
| Nylon / acetal | Fittings and low-friction hardware — nylon needs a UV-stabilized grade and absorbs water; acetal is poor in sustained UV, so keep it shaded or internal |
The pattern: the "marine" version of a resin is the UV-stabilized, weatherable grade — the standard grade of the same plastic often won't last outdoors. A rough pairing by exposure: occasional spray + sun → ASA or UV-stabilized HDPE; constant wet or abrasion → HDPE/UHMW or UV-grade PP; clear and exposed → hard-coated UV polycarbonate; submerged fittings → the right stainless (316) with a nylon/acetal isolator to break the galvanic path.
Hatches and lids, vents and louvers, consoles and panels, storage boxes and trays, trim and rub rails, grab handles, cleats and fittings, seating components, and non-slip treads — molded, and where needed combined with metal hardware and assembled.
"Marine-grade" on its own isn't a certification, so the useful thing is to specify the actual requirement — a UV-weathering target, a salt-spray exposure, a hardware grade — which a material and finish can be chosen and verified against. And if a part is safety-critical or structural (flotation, fuel, steering, or any function covered by USCG regulations or ABYC voluntary standards), the engineering and certification are the customer's or a naval architect's, not JCH's. JCH coordinates the build to the material, finish, and dimensional spec you provide; it doesn't self-certify a marine safety rating for a part it doesn't engineer. Non-regulated parts — trim, storage, housings — are built to your spec through the network.
The part (drawing, CAD, or sample) and, above all, its exposure — full UV, salt immersion or just spray, submersion, abrasion, temperature range. Then the material, color, and finish (or the performance target, and a material can be recommended), any standard it must meet, and your annual volume. The exposure is the key input: a part that sees occasional spray and one submerged in salt want different resins and hardware.
Does JCH make marine and boat parts?
Yes — molded, metal, and assembled parts coordinated through a network: hatches, vents, consoles, panels, storage, trim, handles, cleats, fittings, non-slip treads. The defining challenge is the environment (UV, salt, moisture, impact), so material and finish drive the design — the wrong resin chalks or corrodes within a season or two.
What makes a part "marine-grade"?
Requirements, not a stamp: UV resistance (no chalk/yellow), corrosion resistance (plastics over metal; stainless/anodized/coated hardware), water handling (seal/gasket/drain), impact, and molded-in UV-stable color (not peeling paint). "Marine-grade" alone isn't a certification — specify the real UV/salt/hardware requirement; JCH builds to it, doesn't self-declare a rating.
Which materials are best for marine parts?
Weatherable grades: ASA (most UV-stable common styrenic, ABS-like, exterior trim/housings), HDPE/UHMW (tough, non-marking; UV grade for sun), PP (moisture/chemical; UV grade, brittle in cold), UV-stabilized + hard-coated PC (clear windows; crazes with fuel/solvents — check), nylon/acetal (fittings; nylon needs UV grade + absorbs water, acetal poor in UV). The marine version of a resin is its UV-stabilized, weatherable grade.
Do you handle marine certifications (ABYC/USCG)?
No. Safety-critical/structural parts (flotation, fuel, steering, or anything covered by USCG regulations or ABYC voluntary standards) are the customer's or naval architect's engineering and certification. JCH coordinates molding, metal, and assembly to your spec (including weathering/corrosion requirements) but doesn't self-certify a marine safety rating. Non-regulated parts are built to your spec through the network.
What do you need to quote a marine part?
The part (drawing/CAD/sample) and its exposure (UV, spray vs immersion, submersion, abrasion, temperature), the material/color/finish or performance target, any standard (weathering/salt-spray/hardware/regulatory), and annual volume. Exposure is the key input — occasional spray vs salt submersion want different resins and hardware.
JCH Design & Manufacturing can coordinate marine and boat parts to your spec through its network. Send the part and its exposure — UV, spray or immersion, temperature.
Book a 30-minute call