Yes — JCH coordinates protective cases and the custom foam inserts that cradle what's inside, through a manufacturing network. A case is really two problems: the case (protection, sealing, latching, carry) and the insert (holding the product, absorbing shock, organizing parts). The foam is what makes any case fit your product.
JCH coordinates the case, foam, and assembly through the network; this page is general guidance, not a quote.
The trade-off is sealing and scale: a sealed or IP-rated case is usually an injection-molded or a standard sealed case, while a large hollow shell is blow-molded. For example, a drone kit ships well on a standard sealed case with a PE-foam insert — no tooling, full protection — and only moves to a custom molded case if the volume and branding justify it.
| Foam | Character & use |
|---|---|
| Polyethylene (PE) | Firm, durable — holds a precise pocket and supports heavier items; the common structural choice |
| Polyurethane (PU) | Soft, low-density, cushioning — light or delicate items; conforms closely for a soft touch |
| EVA | Denser and tougher than PU, water-resistant, with a premium finish — higher-end cases |
| Molded foam (EPS / EPP) | Shaped directly at higher volume |
The deciding factor is the product's weight and fragility against the drop or shock it must survive: a heavier item wants firmer, denser foam; a delicate one wants softer foam — with the density and thickness tuned to absorb the impact energy. Foam that's too soft bottoms out and lets the product strike through; foam that's too firm transmits the shock instead of absorbing it.
PE and PU are the common cut-foam stocks (CNC-routed, waterjet, or die-cut to shape) — PE and EVA are closed-cell and water/dust-resistant, while PU is usually open-cell (softer, but it breathes and can absorb water). EPS and EPP are typically molded-in-place or packaging-grade at higher volume — EPS is brittle and single-impact, while EPP is resilient and survives repeated impacts. As a generic reference, PE insert foam commonly runs around 1.7–2.2 lb/ft³, with firmer grades higher.
The pocket is shaped to the product — CNC routing or waterjet for a precise contoured cavity, die-cutting for simpler layered shapes, molded foam at high volume. The details that make an insert usable: finger scallops to lift the product out, layers or trays for multiple items, labeled positions, and closed-cell foam (PE or EVA, not open-cell PU) where water or dust resistance matters. The fit is snug but not forced — the pocket is sized to hold the product with light compression and no play (a slight interference so the foam grips rather than lets it rattle), and where a lid presses on the foam that compression is designed in. In a network, the case and the foam often come from different partners, so the pocket is cut to the measured case, not the spec sheet — a case's internal dimension varies lot to lot — and the sample or CAD model is handed between them so the fit is reconciled before volume, not discovered in the first shipment. The layout comes from the product's shape, weight, and which faces need the most cushioning, and it's cut from a sample or model of the product.
| Choose… | When |
|---|---|
| Custom molded case | Higher volume, a specific shape, a sealed/rugged rating, or branding molded in — carries tooling, but it's exactly yours |
| Standard case + custom foam | Lower volume or a prototype — faster and cheaper, and the foam still gives a precise internal fit |
Many products start on a standard case with custom foam and move to a fully molded case once volume justifies the tooling.
A worked example (illustrative): a ~2 kg instrument rated to roughly a 1 m drop wants a firmer PE grade with a top and bottom cushioning layer, the cavity sized so the unit can't shift sideways, and the extra foam budgeted on the faces it actually lands on — not one uniform block.
The product (dimensions, weight, a sample or model), how it has to be protected (a drop height or shock requirement, water/dust resistance, temperature), how many items per case and whether they're layered, your branding and any sealed/rugged rating, and your annual volume. The weight-and-fragility against the drop requirement sets the foam; the volume decides whether a custom case earns its tooling.
Does JCH make protective cases and foam inserts?
Yes — a case (molded, blow-molded, thermoformed, or a sourced standard case) plus a custom foam insert, coordinated through a network. The case protects; the foam cradles the product and absorbs shock. At low volume, a standard case + custom foam is the fast, low-cost route.
What foam is used?
PE (firm/durable — structural, heavier items), PU (soft/cushioning — delicate), EVA (tough/water-resistant/premium), or molded EPS/EPP at volume. The driver is weight + fragility vs the drop/shock: heavier → firmer/denser; delicate → softer, with density and thickness tuned to the impact.
Custom case or standard case + foam?
Custom molded case for higher volume, a specific shape, a sealed/rugged rating, or molded-in branding (carries tooling). Standard case + custom foam for low volume or a prototype — faster, cheaper, still a precise internal fit. Many start on the latter and graduate to a molded case.
How is the insert made to fit?
CNC routing or waterjet for precise contoured cavities, die-cutting for simpler layered shapes, molded foam at volume — plus finger scallops, layers/trays, labeling, and closed-cell foam for water/dust resistance. Snug, not forced; cut from a sample or model.
What do you need to quote one?
The product (dimensions, weight, sample/model), protection requirement (drop/shock, water/dust, temperature), items-per-case and layering, branding and any sealed/rugged rating, and annual volume. Weight-and-fragility vs the drop sets the foam; volume decides the custom-case tooling.
JCH Design & Manufacturing can coordinate a case and custom foam insert for your product. Send the product dimensions, weight, and how it must be protected.
Book a 30-minute call