Answers › Weld lines & knit lines

Weld lines and knit lines in injection molding: why they weaken and show on parts, and how to prevent them

A weld line (also called a knit line; where the fronts merge at a shallow angle it is often called a meld line) is the seam left where two melt fronts flow apart and meet again — around a hole, past an insert, or between two gates. The join is weaker because the chains never fully re-entangle and air and contaminants collect there, and it is often visible as a faint notch or color change. You rarely delete every weld line; the job is to make it knit hot and steer it off load paths and show surfaces.

Finished injection-molded totes coming off the presses, the kind of thin-wall part where flow fronts split around ribs and handle cut-outs and knit on the far side
Molded parts leaving the presses. Thin-wall parts like these force the melt to split around ribs, handle openings, and bosses — every split becomes a knit line somewhere downstream.

What a weld line actually is

Picture the melt entering an empty cavity as a single advancing front. The moment that front reaches anything it cannot flow straight through — a cored hole, a boss, a metal insert, the edge of a window — it splits into two streams that go around either side. On the far side the two streams meet again and have to fuse back into one body of plastic. That meeting seam is the weld line. The same thing happens when a part has more than one gate: each gate launches its own front, and the fronts collide somewhere in the middle of the part. Whether you call it a weld line or a meld line is mostly about the geometry of the meeting. When the two fronts arrive nearly head-on and stop against each other, we call it a weld line; when they flow more or less side-by-side and merge at a shallow angle, it is usually called a meld line and tends to be a little stronger because the fronts shear along each other as they join. Both are the same underlying event: two surfaces of partly-cooled plastic trying to become one.

gate hole weld line (fronts meet & rejoin)
The melt splits around the hole and knits on the downstream side; the dashed line is the weld.

Why the seam is weaker

Two mechanisms stack up at the meeting line. The first is molecular entanglement. In the bulk of a molded part, the long polymer chains are thoroughly tangled through each other, and that tangle is what carries load. When two fronts meet, each one already has a slightly cooled, higher-viscosity skin on its leading edge, so the chains across the seam do not diffuse and re-tangle the way they would in fully molten plastic. You end up with a plane where the two sides are touching but not properly knitted — mechanically it behaves like a partial bond. The second mechanism is contamination. A flow front acts like a tiny plow: as it advances it pushes air, moisture vapor, volatiles from the resin, and any mold-release or degraded material ahead of itself. When two fronts collide, everything they have been pushing gets trapped right at the junction. That trapped layer is a thin, weak, sometimes voided notch running through the wall. Add the two effects together and the weld plane is the natural crack-starter of the part.

How much strength you actually lose is not a fixed number — it depends on the resin, how hot the fronts were when they met, how far from the gate the line sits, and especially on fillers. As a representative range, an unfilled weld line might hold somewhere around 40 to 90 percent of the surrounding wall's tensile strength; a hot, shallow-angle meld near the gate lands high in that band, a cold head-on weld at the far end of a thin wall lands low. Engineering estimate, not a quote — use a real test or a mold-filling study for a number you can design to.

Why it also shows

Even when a weld line is strong enough, it can still fail you cosmetically. The same frozen-skin meeting that weakens the joint also leaves a small V-shaped surface notch where the two fronts pressed together, and that notch catches light as a hairline. On textured surfaces it can read as a dull streak; on gloss it can read as a faint crease. Pigments make it worse: with metallic or pearlescent colorants the flake orientation changes where the fronts meet, so the weld shows up as a visible color or sheen line even on a part that is structurally fine. That is why you treat a weld line on a Class-A show surface as seriously as one on a load path, and why you tell the molder up front which faces are cosmetic.

Where they form

A mold-filling simulation shows every one of these before steel is cut, which is the whole argument for running it during design rather than discovering lines on first shots.

The knobs that fix them

You generally cannot make a split-and-rejoin disappear, so the goal is to make the fronts knit hot and to put the resulting line where it does no harm. In rough order of what to reach for first:

  1. Run hotter and faster. Raise melt temperature, raise mold (tool) temperature, and raise injection speed so both fronts are still hot and low-viscosity when they meet. A hot knit re-entangles far better than a cold one, and faster fill gives the fronts less time to skin over before they collide. This is the cheapest lever because it is pure process.
  2. Move the line with the gate. Relocating a gate, or adding/removing one, changes where the fronts meet. If a weld currently crosses a snap arm or a show face, a new gate position can drop it onto a hidden rib instead. Fewer gates means fewer weld lines, at the cost of fill pressure and time.
  3. Lead the flow or bleed it off. A flow leader (a locally thickened channel) keeps a path hot and balances when the two fronts arrive so they knit instead of stagnating. An overflow well (a sacrificial pocket just past the meeting point) pulls the cold front edge and its trapped contaminants off the functional part; you trim the well afterward and the good material ends up at the seam.
  4. Vent the junction. The gas pushed ahead of the fronts has to go somewhere. A vent at the predicted weld location lets trapped air and volatiles escape instead of being compressed into the seam (where it can even burn — a dieseling scorch mark right on the line). Venting both strengthens and cleans up the weld.
  5. Pick an easier-flow grade. A higher-melt-flow resin stays fluid longer, so the fronts are hotter when they meet. If strength at the weld is marginal and the grade allows it, an easier-flowing version of the same family can lift the weld strength with no tooling change.

Why fillers — especially glass — make it worse

This is the one that catches people out on structural parts. In a glass-fiber-reinforced resin, most of the stiffness and strength comes from fibers that align themselves along the direction of flow. Through the bulk of the wall that alignment is a feature. But at a weld line the two fronts arrive end-to-end and stop, so the fibers line up parallel to the seam rather than bridging across it. Nothing reinforces the joint — the weld is held together only by the weak polymer matrix, with the fibers doing almost no work across the plane. The practical consequence is that glass-filled parts lose proportionally the most strength at a weld line: where an unfilled grade might keep much of its strength, a 30%-glass grade can keep only about a third of its own no-weld strength at the seam (one published polypropylene example: about 90% retention unfilled vs 34% with 30% glass). (Representative, not a spec.) The right response is not to try to strengthen the weld in glass-filled material — it is to design the weld line out of the load path entirely: move the gate, add a gate, or re-shape the feature so the seam never crosses anything that carries force.

When a weld line is acceptable — and when it is not

SituationWeld line verdict
Hidden surface, no loadAcceptable — most parts have several and work fine
Cosmetic / Class-A show faceAddress it — steer the line off the visible area, run hot, consider texture
Structural load path (snap, boss, hinge, bracket)Eliminate from the path — move the gate; in glass-fill, mandatory
Sealing or pressure-containing wallEliminate or qualify — a weld is a leak/burst starter; test it

Most weld lines are harmless and you leave them alone. The ones that matter are where the line meets a requirement — looks, strength, or seal. The trick is knowing which is which before the tool exists, because moving a weld line after the mold is cut means a gate change or a steel change, not a dial adjustment.

From the tooling floor

A quick habit that saves a lot of back-and-forth: on your drawing, mark the cosmetic surfaces and the load-bearing features explicitly, and say so in words — "this snap arm is structural," "this face is Class-A." A weld line that lands on a hidden boss is a non-event; the same line on a visible corner or across a flexing arm is a return. When the molder knows your intent, the gating and venting get designed around it from the first layout instead of being chased on the press after first shots. It is the single cheapest thing an inventor or designer can hand us.

What to tell your molder

Common questions

What is a weld line / knit line? The seam where two melt fronts split and rejoin — around a hole, insert, or between gates. Weld or knit line = fronts meet head-on; meld line = fronts merge side-by-side at a shallow angle (usually a bit stronger).

Why is it weaker? The cooled front skins don't fully re-entangle, and air plus contaminants get trapped at the junction, leaving a notch. Representatively ~20–100% of wall strength (lowest with glass fill), lower when cold and far from the gate.

Why does it show? A small surface notch catches light, and pigment/flake orientation shifts at the seam — visible on gloss and metallic colors even when strength is fine.

How do you fix it? Run hotter/faster so fronts knit hot; move or add/remove a gate to relocate the line; add a flow leader or overflow well; vent the junction; pick an easier-flow grade.

Why is glass fill worse? Fibers align parallel to the seam instead of bridging it, so glass-filled parts lose the most strength at a weld — design the line out of the load path.

JCH Design & Manufacturing can review your part for weld-line risk — run a mold-filling study, place the gates to steer lines off your show surfaces and load paths, and flag where a glass-filled feature needs the weld designed out entirely, all before any steel is cut. Send your part and say which surfaces are cosmetic and which features carry load; NDA first. Engineering estimate, not a quote.

Book a 30-minute call