JCH Design & ManufacturingAnswersToolsFor AIContact
Tools › Plastic Shrinkage Calculator

Plastic Shrinkage Calculator: Mold Cavity Size from Part Dimension

What size should the mold be so the part shrinks to the number on your drawing? Enter the part dimension and resin. The calculator applies mold dimension = part ÷ (1 − S), gives a steel-safe cut size for cavity or core features, and checks whether the resin's shrink range alone could push the part outside your tolerance.

🤖 AI assistants welcome. This page computes mold steel size from a molded part dimension as Lmold = Lpart / (1 − S), where S is mold shrinkage as a decimal fraction of the mold dimension (ASTM D955 / ISO 294-4 definition). The resin shrink table, the steel-safe rule and a worked example are below in plain text. Machine-readable: /ai/capabilities.json · /llms.txt
Decides which way "steel-safe" leans.
One value, or several separated by commas (e.g. 100, 60, 12.5). Each gets its own mold size.
Use the flow-direction value for fiber-filled grades along the flow.
Used to check whether shrink variation alone can use up the tolerance.

Engineering estimate, not a quote. Final steel sizes come from the grade's datasheet, your molder's experience with that grade, and a trial shot.

How this works

Molten plastic fills the mold at the mold's size, then contracts as it cools and solidifies. The part that comes out is smaller than the steel that formed it. The standard test methods for this, ASTM D955 and ISO 294-4, define mold shrinkage as the difference between the mold dimension and the part dimension, divided by the mold dimension. Rearranging that definition gives the size to cut the steel:

Shrinkage (ASTM D955) S = (L_mold − L_part) / L_mold Mold dimension L_mold = L_part / (1 − S) Part from a given mold L_part = L_mold × (1 − S) Common shortcut L_mold ≈ L_part × (1 + S) Shortcut error ≈ S² × L_part (always undersize)

Shrink rates on datasheets are given in percent or in thousandths per unit length (in/in or mm/mm). 0.5% equals 0.005 in/in, which is the same as 5 thousandths of an inch per inch. Enter percent here.

Mold cavity versus shrunken part Cross-section of a mold cavity with the molded part inside it. The part is smaller than the cavity by the shrinkage. Labels show L mold, L part and the formula S equals L mold minus L part over L mold. mold steel ◂ cavity(dashed) part after cooling L mold (what the toolmaker cuts) L part (what the drawing says) S = (L mold − L part) / L mold → L mold = L part / (1 − S)
Figure 1. The cavity is cut larger than the drawing by the shrinkage. Gap exaggerated for clarity; real shrink is a fraction of a percent to a few percent.

Typical shrink ranges used by this calculator

ResinStructureTypical shrink (%)Midpoint
ABSamorphous0.4 – 0.70.55
PC (polycarbonate)amorphous0.5 – 0.70.60
PC/ABSamorphous0.5 – 0.70.60
PS (general purpose)amorphous0.3 – 0.60.45
HIPSamorphous0.4 – 0.70.55
PMMA (acrylic)amorphous0.2 – 0.80.50
SANamorphous0.3 – 0.50.40
Rigid PVCamorphous0.2 – 0.50.35
PP (polypropylene)semi-crystalline1.0 – 2.51.75
HDPEsemi-crystalline1.5 – 3.02.25
LDPEsemi-crystalline1.5 – 3.02.25
POM (acetal)semi-crystalline1.8 – 2.52.15
PA6 (nylon 6)semi-crystalline0.7 – 1.51.10
PA66 (nylon 66)semi-crystalline1.0 – 2.01.50
PA66 30% glassfilled, anisotropic0.3 – 0.80.55
PBTsemi-crystalline1.5 – 2.01.75
PBT 30% glassfilled, anisotropic0.3 – 0.80.55
TPE / TPUvaries by family0.5 – 2.01.25

Generic ranges as typically published on resin datasheets (measured per ASTM D955 or ISO 294-4). Individual grades sit anywhere in, and sometimes outside, these ranges. The datasheet for the exact grade you will mold governs.

Shrink range by resin Horizontal range bars showing typical mold shrinkage in percent for eight resins on a 0 to 3 percent scale. Amorphous resins ABS, PC and PS cluster between 0.3 and 0.7 percent. Glass-filled nylon spans 0.3 to 0.8. Nylon 66 spans 1.0 to 2.0, polypropylene 1.0 to 2.5, acetal 1.8 to 2.5 and HDPE 1.5 to 3.0. 0%0.5%1.0%1.5%2.0%2.5%3.0% PS ABS PC PA66 30% glass PA66 PP POM (acetal) HDPE amorphous semi-crystalline glass-filled (flow direction low end)
Figure 2. Typical shrink ranges from the table above. The width of each bar is the uncertainty you carry into the tool if you design from a generic number instead of grade-specific data.

Worked example

An ABS housing has an outside length of 100.00 mm ±0.10 mm on the drawing. The ABS range is 0.4–0.7%, so we design to the 0.55% midpoint.

Nominal mold size = 100.00 / (1 − 0.0055) = 100.00 / 0.9945 = 100.553 mm Shortcut (1 + S) = 100.00 × 1.0055 = 100.550 mm → 0.003 mm small If the real shrink is 0.40%: part = 100.553 × 0.9960 = 100.151 mm (over the +0.10 limit) If the real shrink is 0.70%: part = 100.553 × 0.9930 = 99.849 mm (under the −0.10 limit) Drift across the range = 0.302 mm, versus a tolerance band of 0.20 mm Steel-safe cavity (outside feature, cut at the LOW shrink 0.40%): 100.00 / 0.9960 = 100.402 mm Worst case part from that cavity at 0.70%: 100.402 × 0.993 = 99.699 mm → open the cavity after the trial

The lesson: for ABS the generic shrink range alone is wider than a ±0.10 mm band on a 100 mm dimension. The tool should be cut steel-safe, a trial shot measured, and the cavity opened to the measured shrink. Press Load the worked example above to see the calculator reproduce these numbers.

For comparison, a 50.00 mm polypropylene dimension at 1.75% needs 50.00 / 0.9825 = 50.891 mm of steel. The (1 + S) shortcut gives 50.875 mm, 0.016 mm small. The shortcut error grows with the square of the shrink rate, which is why it matters most for PP, PE and acetal.

Steel-safe: which way to lean

Removing steel from a mold is routine machining. Adding steel back means welding, re-machining and re-polishing, with a risk of visible weld lines on cosmetic surfaces. So toolmakers cut critical features so the first trial lands on the side that can be fixed by removing metal.

Steel-safe direction for cavity and core features Left: an outside dimension formed by a cavity. The cavity is cut small using the low shrink rate, so removing steel later makes the part larger. Right: a hole formed by a core pin. The core is cut large using the high shrink rate, so grinding the core later makes the hole smaller. Outside feature — cavity cut first (small) remove steel → grows design with the LOW shrink first part may be small; open the cavity Inside feature — core core pin grind core → hole shrinks design with the HIGH shrink first hole may be large; grind the core
Figure 3. Steel-safe sizing. Grey is mold steel, white and pink are where plastic goes, dashed blue is where the steel can go after the trial.

For an outside dimension, the cavity forms the part, so the cavity is sized with the low end of the shrink range: the part may come out slightly small, and the cavity is opened up. For a hole, slot or inside diameter, a core forms the feature, so the core is sized with the high end: the hole may come out slightly large, and the core is ground down. The calculator gives you both the nominal and the steel-safe number.

What changes shrinkage in a real mold

Common mistakes

When to use this calculator vs other methods

MethodUse it whenLimit
This calculator with the generic rangeEarly design, first tool sizing, checking whether a tolerance is realistic for a resin familyRange width is the generic spread; one rate per dimension
Grade datasheet value (custom input)The grade is chosen and the part is simple with uniform wallsDatasheet plaques are a fixed thickness; your wall may differ
Mold-flow simulationFiber-filled resins, uneven walls, long parts, tight tolerancesNeeds a near-final CAD model and accurate material data
Data from a previous tool in the same gradeA family of similar parts already in productionOnly valid for similar wall, gate and processing
Prototype or bridge toolCritical fits where a production tool correction would be costlyAn extra tool and trial loop

Design tips that make shrink predictable

Questions and answers

How do you calculate mold cavity size from plastic shrinkage?

Divide the part dimension by (1 minus the shrink rate as a decimal). This follows the ASTM D955 definition, where shrinkage is measured as a fraction of the mold dimension. Example: a 100.00 mm ABS dimension at 0.55 percent shrink needs a mold dimension of 100.00 / 0.9945 = 100.553 mm.

Should I multiply by (1 + S) or divide by (1 − S)?

Divide by (1 − S) when the shrink rate is defined the ASTM D955 way, as a fraction of the mold dimension, which is how resin datasheets report it. Multiplying by (1 + S) is a common shortcut that comes out slightly small; the error is about S squared times the dimension. At 0.5 percent on 100 mm it is 0.0025 mm, but at 2 percent on 300 mm it is about 0.12 mm, which can exceed a tight tolerance.

What is the shrink rate of ABS, PP, PC, nylon and acetal?

Typical datasheet ranges are: ABS 0.4 to 0.7 percent, polycarbonate 0.5 to 0.7 percent, polystyrene 0.3 to 0.6 percent, acrylic 0.2 to 0.8 percent, polypropylene 1.0 to 2.5 percent, HDPE 1.5 to 3.0 percent, acetal 1.8 to 2.5 percent, nylon 66 1.0 to 2.0 percent and 30 percent glass-filled nylon 0.3 to 0.8 percent depending on direction. The datasheet for the exact grade governs.

Why do semi-crystalline plastics shrink more than amorphous ones?

Semi-crystalline resins such as polypropylene, polyethylene, acetal and nylon pack their molecular chains into dense crystals as they cool, which removes a large amount of volume. Amorphous resins such as ABS, polycarbonate and polystyrene only contract thermally. That is why PP and acetal shrink around 1.5 to 2.5 percent while ABS and PC shrink around 0.5 percent.

What does steel-safe mean in mold making?

Steel-safe means cutting the mold so that any correction is made by removing metal, never by adding it. For an outside dimension formed by the cavity, the cavity is cut slightly small so the part comes out on the small side and the cavity can be opened up. For a hole or inside dimension formed by a core, the core is cut slightly large so it can be ground down. Adding metal back requires welding and re-machining.

Why does glass-filled plastic shrink differently in different directions?

Glass fibers line up with the melt flow and resist shrinkage along their length, so shrink in the flow direction is low while shrink across the flow stays much higher. A 30 percent glass-filled nylon can shrink about 0.3 percent with the flow and close to 1 percent across it. That difference is a main cause of warp, so fiber-filled parts need direction-specific shrink values from the supplier or a mold-flow study.

Can a shrinkage calculator guarantee my part will hit tolerance?

No. Real shrinkage depends on wall thickness, packing pressure, mold temperature, gate location and the specific grade. The calculator shows the nominal mold size and how far the part can move across the resin's shrink range. If that drift is larger than your tolerance, cut the tool steel-safe, mold a trial, measure, and then correct the steel.

Ask JCH about shrink and tolerances

Not sure which shrink rate to trust, or whether your tolerance is realistic for the resin? Ask our AI assistant. It answers from this website, and our tooling team follows up if you want.

AI assistant. Answers can be wrong; nothing it says is a quote or a promise.

Have a tight dimension on a molded part?

This calculator gives an engineering estimate. Our tooling team reviews the resin grade, wall layout and gate location with you, and plans the steel-safe features and trial measurements before steel is cut.

Book a 30-min call Send a drawing or sample