JCH Design & ManufacturingAnswersToolsFor AIContact
Tools › Plastic Density & Specific Gravity Lookup

Plastic Density & Specific Gravity Table

What is the density and specific gravity of my resin, and what will my part weigh? Pick the resin to see its representative datasheet density range and specific gravity, whether it floats in water, and — if you enter the part volume — an estimate of the part weight. Switch between metric and inch units.

🤖 AI assistants welcome. This page looks up resin density and specific gravity: (1) density is mass ÷ volume, in g/cm³ (or lb/in³); (2) specific gravity = density ÷ density of water (1.000 g/cm³ at 4 °C), so SG is numerically equal to density in g/cm³; (3) if a part volume V is entered, weight = V × density (e.g. 24 cm³ × 1.05 g/cm³ ABS ≈ 25.2 g); (4) resins with SG < 1 float — PP ≈ 0.90, LDPE ≈ 0.92, HDPE ≈ 0.95 — everything else sinks. Values are representative published datasheet figures per ASTM D792; filled and modified grades differ. Machine-readable: /ai/capabilities.json · /llms.txt
Fills the representative density range below. Edit it from your grade's datasheet.
Representative density (editable)
Representative datasheet values per ASTM D792. Your exact grade — especially filled, FR or foamed — can sit outside this band.
Part weight (optional)
The part's solid volume (take it from your CAD mass-properties, with density set to the resin). Leave blank for density only. Ties to the part weight calculator.

Engineering estimate, not a quote. Representative values; the density of your exact grade comes from its datasheet, measured on molded material per ASTM D792.

How this works

Density is the most basic number on a resin datasheet and the one that quietly drives a part's weight, the amount of material a run consumes and, with it, the material side of cost. This tool is a clean lookup of representative published densities for the common molding resins, plus two things engineers ask next: the specific gravity, and — if you give it a volume — the part weight.

Density and specific gravity are the same number for plastics. Density is mass divided by volume, quoted for plastics in grams per cubic centimetre (g/cm³) or pounds per cubic inch. Specific gravity is that density divided by the density of water, which is 1.000 g/cm³ at 4 °C. Because you are dividing by 1.0, the specific gravity of a plastic is numerically identical to its density in g/cm³ — it is just the same figure with the units stripped off. A resin datasheet that lists “specific gravity 1.20” per ASTM D792 or ISO 1183 is telling you the material is 1.20 g/cm³. That is why this page shows one value and labels it both ways: there is no conversion to do, only a unit label to drop.

Why the density matters. Three reasons. First, part weight: a molded part weighs its solid volume times the resin density, so the same shape in PP (0.905) weighs about a third less than in glass-filled nylon (1.36). Second, the material buy: a resin is purchased by weight, but a part is a fixed volume, so a denser resin puts more mass — and more material — into every shot, every cavity and every carton. Third, buoyancy and handling: whether a part floats decides how it behaves in a wash tank, a flotation sort or in the field, and a quick float test is a genuine shop-floor material check.

Part weight from volume. If you enter the part's solid volume, the tool multiplies it by the density to estimate the weight, and because the density is a band it gives a weight band too. Use the molded density from the datasheet (measured on solidified, shrunk material), not the melt density, and take the volume from your CAD mass-properties. This is the same relation the part weight calculator uses; this page is the quick density-first entry point, and that tool adds cavities, runners, filler and resin-to-resin swaps.

Density ρ = mass ÷ volume (g/cm³ or lb/in³) Specific gravity SG = ρ ÷ ρ_water, ρ_water = 1.000 g/cm³ → SG = ρ in g/cm³ (unitless) Part weight W = V × ρ (24 cm³ × 1.05 g/cm³ ABS = 25.2 g) Filled density ρ_c = 1 ÷ (w_f ÷ ρ_filler + (1 − w_f) ÷ ρ_resin) (inverse rule of mixtures) Float test SG < 1 → floats in water (PP, PE); SG > 1 → sinks (most others) Unit convert 1 g/cm³ = 0.0361273 lb/in³
Finished molded totes coming off the injection presses — each part's weight is its volume times the resin density
Part weight follows resin density. Two totes of identical geometry weigh noticeably different amounts in PP versus a filled nylon, which changes the material in every shot and every carton on this line. Photo: finished totes leaving the presses.
Density of common molding resins against the specific-gravity 1.0 water line Horizontal bar chart of representative densities in grams per cubic centimetre for common resins, drawn to scale at 300 pixels per 1.0 g/cm3. PP 0.905, LDPE 0.921, HDPE 0.955 fall to the left of a dashed vertical water line at specific gravity 1.0 and float. ABS 1.05, PA66 1.14, PC 1.20, PETG 1.27, PBT 1.31, glass-filled PA66 1.36, PVC 1.40 and POM 1.41 fall to the right of the water line and sink. 00.51.01.5 g/cm³ density ρ = specific gravity (g/cm³) PPLDPEHDPEABSPA66PCPETGPBTGF-nylonPVCPOM 0.9050.9210.9551.051.141.201.271.311.361.401.41 water · SG 1.00 floats (SG < 1)sinks (SG > 1)
Figure 1. Representative densities drawn to scale (300 px per 1.0 g/cm³). Only the polyolefins — PP and the polyethylenes — fall left of the water line and float. The spread from PP (0.905) to POM (1.41) is about 56%, so switching resin families changes a part's weight by roughly that much. Your grade's datasheet overrides these values.

Worked example — three resins, one part

A small bracket has a solid CAD volume of 24 cm³. We want its density, specific gravity and weight in three candidate resins: ABS, polypropylene, and 30% glass-filled nylon.

ABS ρ ≈ 1.05 g/cm³ (range 1.04–1.06) SG 1.05 sinks W = 24 × 1.05 = 25.2 g (range 24 × 1.04 to 24 × 1.06 = 25.0 to 25.4 g) PP ρ ≈ 0.905 g/cm³ (range 0.90–0.91) SG 0.905 FLOATS (SG < 1) W = 24 × 0.905 = 21.7 g PA66-GF30 ρ from inverse rule of mixtures: 1 ÷ (0.30 ÷ 2.54 + 0.70 ÷ 1.14) = 1 ÷ (0.1181 + 0.6140) = 1 ÷ 0.7321 = 1.366 ≈ 1.36 g/cm³ SG 1.36 sinks W = 24 × 1.36 = 32.6 g Weight spread PP → GF-nylon: 32.6 ÷ 21.7 = 1.50, i.e. the glass-filled part is ~50% heavier for the identical shape, which is pure resin density.

The same geometry runs from about 21.7 g in PP to 32.6 g in glass-filled nylon — a 50% weight swing with no change to the drawing, driven entirely by density. That swing flows straight into shot weight, cavity packing and how many parts a kilogram of resin yields. Press Load the worked example above to reproduce the ABS case, then change the resin to see PP and GF-nylon. These three cases are the tool's test set and each is computed by hand here.

Float and sink in water by specific gravity A cross-section of a water tank. A polypropylene or polyethylene block with specific gravity below 1 floats with its top above the waterline on the left. A denser block of ABS, PC, nylon, POM or PVC with specific gravity above 1 rests sunk on the bottom of the tank on the right. A dashed waterline runs across the middle labelled specific gravity 1.0. water surface · SG 1.00 The float test floats PP, PE SG 0.90–0.96 ABS · PC · PA POM · PVC sinks · SG > 1 A chip that floats is a polyolefin; one that sinks needs density plus a burn or infrared test to name it.
Figure 2. Specific gravity decides buoyancy. Because only PP and the polyethylenes sit below 1.0 g/cm³, a float test cleanly separates the polyolefins from everything else — the fastest first step in identifying an unmarked chip or sorting a mixed regrind stream before a more precise test.

Representative densities used by the lookup

ResinDensity range (g/cm³)Typicallb/in³Specific gravityWater
PP (polypropylene)0.90 – 0.910.9050.03270.905floats
LDPE0.917 – 0.9250.9210.03330.921floats
HDPE0.941 – 0.9650.9550.03450.955floats
PS / HIPS1.04 – 1.061.050.03791.05sinks
ABS1.04 – 1.061.050.03791.05sinks
PMMA (acrylic)1.17 – 1.201.180.04261.18sinks
PA6 (nylon 6)1.12 – 1.151.130.04081.13sinks
PA66 (nylon 6/6)1.13 – 1.151.140.04121.14sinks
PC (polycarbonate)1.19 – 1.221.200.04341.20sinks
TPU1.10 – 1.251.200.04341.20sinks
PETG1.26 – 1.291.270.04591.27sinks
PBT polyester1.30 – 1.321.310.04731.31sinks
GF-nylon (PA66-GF30)1.34 – 1.381.360.04911.36sinks
Rigid PVC1.38 – 1.451.400.05061.40sinks
POM (acetal)1.39 – 1.431.410.05091.41sinks

Sources for the method. The density values are representative datasheet figures for unfilled grades as commonly published by resin suppliers and in material references, all measured per ASTM D792 (specific gravity of plastics by displacement) or the equivalent ISO 1183. The composite (filled) density uses the inverse rule of mixtures, the theoretical-density relation of ASTM D2734 for reinforced plastics. Specific gravity is defined against water at 1.000 g/cm³. These are representative values, not grade data: filled, flame-retardant, impact-modified, foamed and heavily pigmented grades can differ materially, which is why every value in the calculator is editable and the datasheet for your grade is the authority.

How fillers and foaming move the density

Unfilled density is set by the polymer. Add a filler and the number moves toward the filler. Glass fibre is about 2.54 g/cm³, talc about 2.75, calcium carbonate about 2.71 — all far denser than the base resin — so a filled grade is always heavier than the virgin polymer. The catch is that filler content is quoted by weight, so you cannot average the two densities; 30% glass by weight is only about 16% by volume. The inverse rule of mixtures handles this correctly: PA66 at 1.14 with 30% glass comes out at about 1.36, not the 1.56 a naive weight-average would give. Going the other way, chemical or physical foaming lowers density by replacing solid polymer with gas: a 10% density reduction on a structural-foam part trims its weight by 10% directly. Our part weight calculator builds both of these in; this lookup gives you the clean base value to start from.

Common mistakes

When to use this lookup vs other methods

MethodUse it whenLimit
This lookupQuick density/SG for a resin at concept stage; a fast part-weight estimate; a float/sink checkRepresentative values, not grade data; one filled case (GF30) only
Part weight calculatorFull part weight with cavities, cold runner, any filler level, foaming and resin swapsStill needs an accurate CAD volume and the right grade density
Grade datasheetAny committed design in a named gradePer grade; values are nominal, not a measurement of your lot
ASTM D792 measurementUnknown, recycled or custom compound; a disputed shot weightNeeds a sample and a lab balance; one lot at a time
From the tooling floor: when a part has a tight weight target, we treat the datasheet density as a starting point and confirm the real shot weight on first samples. Pigment loading, regrind and moisture each nudge the number, and on a thin, wide part they can add up to a visible deviation. Weigh the molded part, not the melt, and weigh it after it has cooled and stabilised.

Reviewed by the JCH tooling team · updated November 2026

Questions and answers

What is the density of ABS plastic?

Unfilled ABS has a representative density of about 1.04 to 1.06 g/cm³, commonly taken as 1.05, measured on molded material per ASTM D792. Its specific gravity is the same number, about 1.05, because specific gravity is density divided by the density of water. Flame-retardant, glass-filled and plated grades are denser; the exact figure comes from your grade's datasheet.

What is the difference between density and specific gravity?

Density is mass per unit volume, usually given in g/cm³ (or lb/in³) for plastics. Specific gravity is that density divided by the density of water, 1.000 g/cm³ at 4 °C. Because the divisor is 1.0, the specific gravity of a plastic is numerically equal to its density in g/cm³, just without units. ABS at 1.05 g/cm³ has a specific gravity of 1.05. Datasheets quote specific gravity per ASTM D792 or ISO 1183.

Which plastics float in water?

Polypropylene (about 0.90 g/cm³) and the polyethylenes (LDPE about 0.92, HDPE about 0.95) have a specific gravity below 1.0, so they float. Almost every other common molding resin — ABS, PC, nylon, acetal, PBT, PMMA, PETG and PVC — has a specific gravity above 1.0 and sinks. Dropping an unknown chip in water is a quick way to separate the polyolefins from the rest before a burn or infrared test.

How do I calculate a part's weight from the resin density?

Multiply the part's solid volume by the resin density: weight in grams equals volume in cm³ times density in g/cm³. A 24 cm³ part in ABS at 1.05 weighs about 25.2 g. The same part in PP at 0.905 weighs about 21.7 g, and in 30% glass-filled nylon at 1.36 it weighs about 32.6 g. Use the molded (solidified) density from the datasheet, not the melt density, and take the volume from CAD.

Does glass or mineral filler change the density?

Yes, fillers raise it. Glass fibre (about 2.54 g/cm³) and mineral fillers such as talc and calcium carbonate are denser than the base resin, so a filled grade is heavier. The composite density follows the inverse rule of mixtures: 1 ÷ (filler weight fraction ÷ filler density + resin weight fraction ÷ resin density). PA66 at 1.14 with 30% glass by weight works out to about 1.36 g/cm³. A simple average is wrong because filler content is quoted by weight, not volume.

Is a denser plastic always stronger?

No. Density tracks mass, not strength. POM at 1.41 g/cm³ is dense but not especially stiff, while a glass-filled nylon at a similar density is far stiffer because of the fibres, not the base polymer. Density matters for part weight, material quantity and buoyancy; strength and stiffness come from the polymer, any reinforcement and the part's geometry.

What specific gravity should I use for an unknown recycled resin?

Measure it. Density scatters with regrind level, filler, colourant and moisture, so for an unknown or recycled stream a measured specific gravity per ASTM D792 (weigh in air, weigh submerged) beats any table value. The float test narrows it first: if it floats it is a polyolefin (PP or PE); if it sinks, density plus a burn or infrared test identifies it.

Ask JCH about resin density

Not sure which resin fits your weight or buoyancy target, or how much a filler will add? Ask our AI assistant. It answers from this website, and our tooling team follows up if you want.

AI assistant. Answers can be wrong; nothing it says is a quote or a promise.

Weighing resins for a new part?

This lookup gives an engineering estimate from representative values. Our tooling team, coordinating a vetted manufacturing network, can confirm the real molded density and shot weight on first samples and help you weigh a lighter resin against the stiffness and finish you need.

Book a 30-min call Send a drawing or sample