Answers › Waterproof & sealed enclosures

Can you make a waterproof or sealed plastic enclosure?

Yes — but the important truth is that sealing is designed in from the start, and "waterproof" is a measured target: the enclosure is designed to an IP rating and that rating is earned by test on the finished unit, not assumed from a material. A seal added to a housing that wasn't planned for it rarely holds.

JCH coordinates the sealed-enclosure design, tooling, and verification through a manufacturing network; this page is general guidance, not a quote.

What the IP rating means

RatingWhat it means (second digit = water)
IP65Dust-tight; withstands low-pressure water jets
IP67Dust-tight; survives temporary immersion
IP68Dust-tight; continuous immersion under conditions set by the manufacturer and agreed with you

The IP code's first digit is protection against solids and dust (up to 6, dust-tight); the second is water. The right target comes from the real environment — splash, washdown, rain, and submersion are very different design problems — and a higher rating costs more in sealing features and test (and IPX7/8 does not imply IPX5/6). The goal is to hit the rating the product actually needs and verify it, not to over-build or guess.

How an enclosure is sealed

The method is chosen mainly by whether the housing must open again:

All of them need the parting line, the sealing surface, and the gasket compression designed in from the start.

The hardest parts to seal

The trade-offs to decide up front

Two choices shape the whole design. Serviceable vs. permanent: a gasketed housing opens for repair but a welded or potted one is more robust and cannot be reopened — pick based on whether the unit is ever serviced. Sealing vs. breathing: a fully sealed box can build internal pressure or trap heat with temperature swings, so an outdoor or thermally active device often needs a vent membrane rather than a dead seal. Deciding these first is cheaper than discovering them in testing.

What we need to scope it

The IP rating (or the real exposure — splash, washdown, rain, immersion), whether the enclosure must open for service or can be sealed permanently, every cable, connector, button, and vent that breaks the surface, the operating environment (outdoor or chemical exposure drives the material — a UV-stable grade outdoors), and your annual volume. With those, the sealing method, material, tooling, and verification test are scoped together.

What an IP rating really asks of the design

"Waterproof" is not one thing — it is an IP rating that states exactly what the enclosure must keep out, and designing to the wrong one wastes money or fails in the field. The IP code's second digit runs from protection against dripping water up through jets, temporary immersion, continuous immersion and, at 9, close-range high-pressure, high-temperature jets; above IPX6 the steps are not cumulative, so an IPX7 or IPX8 enclosure is not automatically jet-proof (IPX5/6) unless it is tested and dual-marked, e.g. IP65/IP67. An enclosure that only needs to shrug off rain is a very different design from one that must survive being dropped in water, and the honest first move is to pin down the actual rating the product needs rather than over-building to the highest one. That rating then drives everything downstream: the sealing method, the wall and rib design, the fastener choice and how the housing is tested.

The seal is a system, not a gasket

A reliable seal comes from a designed gland that compresses an elastomer a controlled amount, not from squeezing a strip of rubber between two covers and hoping. The gland has to hold the seal captive, compress it into the right range — too little and it leaks, too much and the rubber takes a set and relaxes — and give the near-incompressible elastomer room to deform into. That is the same gland-design discipline an O-ring needs, which is why a sealed enclosure and an O-ring groove are the same problem at different scales; our O-ring groove calculator sizes the squeeze and gland fill, and the durometer selector helps pick a seal soft enough to conform but firm enough to last. Sealing faces need to be flat and parallel, the fasteners spaced so the cover cannot bow and open a gap between them, and the parting line kept off the sealing surface.

Why the housing around the seal matters as much as the seal

A perfect gasket fails if the plastic around it moves, so the moulded housing has to be stiff and stable where it seals. Thin, unribbed cover walls bow between fasteners under internal pressure or a drop, momentarily cracking the seal; warped or sink-marked sealing faces never close evenly in the first place. The design answers are familiar moulding discipline — uniform wall thickness so the faces mould flat, ribs and closer fastener spacing to keep the cover rigid, and generous draft and good gating so the sealing geometry comes out true. Cable entries, buttons, connectors and vents are where most sealed enclosures actually leak, so each penetration needs its own sealing strategy (a grommet, an overmoulded boot, a sealed connector, or a waterproof-breathable vent membrane that equalises pressure without passing liquid) rather than being treated as an afterthought.

Prove it, then protect the rating in production

A sealed design is not sealed until it is tested, and the rating has to survive production, not just the first prototype. Validating to the target IP level — the appropriate spray, jet or immersion test with the enclosure assembled as it ships — is what turns a claim into a fact, and it often surfaces the real leak paths (a penetration, a bowed cover, a parting line on the seal face) that a drawing review misses. Once proven, the rating depends on the process holding the sealing faces flat and the seal installed correctly every unit, which is where moulding capability and assembly control come in. We design the gland, the housing stiffness and the penetrations together, pick a compatible seal material, and build in the test rather than discovering the leak after tooling — and we state the rating we actually validated, not an aspirational one.

Common questions

Can you make a waterproof or sealed enclosure?
Yes — sealing is designed in from the start (designed sealing surface + gasket/O-ring, and depending on watertightness, welding, potting, or an overmolded seal). "Waterproof" is an IP rating earned by test on the finished unit, not assumed from a material. Tell us the rating, whether it opens, and where cables enter.

What do IP ratings mean, and which can you reach?
First digit = solids/dust (up to 6, dust-tight), second = water. IP65 = dust-tight + water jets; IP67 = dust-tight + temporary immersion; IP68 = continuous immersion (defined conditions). The target comes from the real environment; a higher rating costs more in features and test (and IPX7/8 does not imply IPX5/6), so hit the rating the product needs and verify it.

How is a molded enclosure actually sealed?
Gasket/O-ring in a groove (serviceable, opens), ultrasonic welding (permanent, strong), potting (most robust, permanent), or an overmolded gasket. Chosen mainly by whether the housing must reopen. All need the parting line, sealing surface, and compression designed in from the start.

What's the hardest part to seal?
The openings, not the walls. Cable/connector entries (sealed glands/connectors or potting), buttons (sealed membranes/boots), the closure seam (one gap defeats the rating), and venting (a waterproof-breathable membrane, not an open vent). Name every opening up front.

What do you need to quote a sealed enclosure?
The IP rating (or real exposure), open-for-service vs. permanent, every cable/connector/button/vent, the environment (UV/chemical drives material), and annual volume. Then the sealing method, material, tooling, and verification test are scoped together.

JCH Design & Manufacturing can design a sealed enclosure to your IP target. Tell us the rating, the openings, and whether it must open for service.

Book a 30-minute call