Answers › Golden sample

What is a golden sample in manufacturing, and how do you use it?

Reviewed by the JCH tooling team · Updated

A golden sample is a part made on the production tool that buyer and factory sign as the physical standard for what a drawing can't pin down: color, gloss, texture, gate marks and feel. Each party keeps a labeled copy per cavity, boundary samples mark the worst acceptable condition, and inspectors judge each lot against that set.

Buyers and factories use several names for the same object: golden sample, master sample, approval sample, reference sample. In every version it's a real part, molded on the production tool from the production material, that both sides have examined and signed as the standard for how the product should look, feel and work. The drawing still rules dimensions. The signed part rules the things a drawing describes badly or not at all.

Why a part needs a physical standard

A drawing can pin a hole diameter down to a tight tolerance. It struggles with a note like "gloss black, no visible flow lines, gate vestige not objectionable." Words like that mean one thing to the designer, another to the press operator and something else again to an inspector who has never seen the product. A signed part ends the argument: hold the production part next to the reference under the same light and it either matches or it doesn't. Prestolite's supplier PPAP handbook describes master samples in these terms, as parts signed by customer and supplier and used to train operators on subjective inspections such as visual checks or noise.

That is also where the idea runs out. A reference part tells you what one good unit looked like. It can't tell an inspector how far a production part may drift before it becomes a reject, and it says nothing about dimensions nobody measured. Boundary samples and the inspection plan fill those gaps.

The reference set: golden, boundary and reject parts

One golden part on its own forces a bad choice. If anything that differs from it is a defect, nearly every production part fails; if small differences are fine, nobody knows where small ends. IPQC's guide to limit samples makes the same point: judge only against a perfect standard and everything not made exactly to the drawing counts as defective. The practical answer is a small family of parts for each subjective attribute.

PartWhat it showsTypical use
Golden (master) sampleThe target: approved look, color, texture and functionPress setup, first-off checks, settling disputes
Boundary (limit) sampleThe worst condition still acceptable for one attribute, such as the deepest allowed sink or the lightest allowed shadeThe inspector's pass/fail line for that attribute
Reject (defect) sampleA condition just past the limitTraining people to recognize the failure
Color or texture plaqueColor or grain on a flat chip rather than on the partApproving color and texture alongside the part

Shade is the easiest case to picture: a target part with one boundary part slightly darker and one slightly lighter, and anything outside that pair is rejected. The same logic works for sink over a boss, gate vestige height, flow lines around a hole or a scuff on a textured face. Each boundary part should name the single attribute it limits. A part labeled boundary for everything is useless, because the inspector can't tell which feature it is meant to show.

A reference set laid out along one appearance attribute: the golden sample in the middle of the accept band, a boundary sample at each acceptance limit, reject samples outside, and the stages where the set is made and used One attribute, five reference parts Example attribute: depth of sink over a boss, or how light or dark the color reads REJECT ACCEPT REJECT reject sample boundary (limit) golden / master sample boundary (limit) reject sample less of the attribute more of the attribute Where the set comes from and where it is used trial shots steel fixes approval run sign set + FAI each lot: AQL Buyer, factory quality and the inspector each hold the set, one golden part per cavity.

Who signs it, and what the signature covers

At minimum the buyer and the supplier sign, and the inspection team works from a copy of the same approved version. In automotive PPAP the master sample is a named element, number 15 of the 18 elements Quality-One lists, described there as a final sample inspected and signed off by the customer. Outside automotive there is no rulebook, so write down what the signature means. A workable wording: this part, from this tool and cavity, molded in this resin grade and color lot, at drawing revision X, is approved for appearance and function; dimensions are approved separately on the inspection report. That last clause matters. A signature on a part nobody measured is an appearance approval, not a dimensional one.

The buyer-side signer should be someone who will still be on the program at reorder time and can say yes or no on cosmetics. A signature from a contractor who has since moved on leaves an orphan standard that nobody can interpret.

Labeling and storage

Treat the reference like a controlled document. Tenneco's PPAP guidelines ask for a tag that identifies the part as a master sample and lists the part number, revision level and part name, the project and customer, the date it was made and the date the approval warrant was signed. They also call for one master sample per cavity on multi-cavity tools, and Prestolite's handbook asks for at least one per cavity, mold or tool. For limit samples, IPQC's guide puts the defect mode and an expiry date on the label and keeps a ledger with each sample's management number and storage location.

A hand lifting a clear molded part off the polished core of an open mold
A part coming off the tool during a molding run. Sign references from parts made this way, on the real tool at real settings, not from prototypes or hand-finished pieces.

How it fits with first article, PPAP and AQL

These steps answer different questions, and mixing them up is where approvals stall. The first article report shows the production process made a part that meets each line of the drawing; the first article inspection checklist covers what that report should hold. The golden part shows what the product should look and feel like. Together they make the approval, and usually the same approval run produces both: measure some parts for the report, sign others as the reference set. The stages before that are covered in samples and first articles.

PPAP bundles all of this. Quality-One lists five submission levels, from a warrant only at level 1 up to complete data available for review at the supplier's site at level 5. Whether a physical master sample is demanded depends on the customer; Prestolite, for one, asks for it case by case and requires it to be on hand if part concerns come up. Parts with color, grain or surface appearance requirements also get an Appearance Approval Report.

AQL sampling then uses the reference set on every lot. The inspector pulls a random sample sized to the lot, checks dimensions against the drawing and appearance against the golden and boundary parts, and counts defects by class. The AQL calculator returns the sample size and the accept and reject numbers, and the quality control and inspection page lists where else checks happen. Without the reference set, the appearance half of that count is opinion.

Quality and test lab with long benches, rows of closed drawers, test instruments and an environmental test cabinet at the back
A quality room away from the press floor, with closed drawers and steady conditions, is the kind of place sealed reference parts belong: out of direct light and easy to find when a lot is in question.

Worked example: sizing the set for a four-cavity part

Take a hypothetical gloss-black ABS housing from a four-cavity tool, ordered in lots of 3,500. Three parties need references: the buyer, the factory's quality team and a third-party inspector.

  1. Golden parts. One per cavity per holder: 4 cavities x 3 holders = 12 parts.
  2. Boundary and reject parts. The team agrees three subjective attributes: sink over the screw bosses, gate vestige, and gloss change near the gate. Each gets one boundary part and one reject part, so 3 x 2 = 6 parts per set. These limits rarely need to differ by cavity, so one set per holder: 6 x 3 = 18 parts.
  3. Total. 12 + 18 = 30 reference parts, plus spares. Boundary and reject parts often have to be made on purpose by nudging the process during the approval run, then sorted, compared and signed, so plan that run with the extra shots in mind.

Now the lot check. For a lot of 3,500 at general inspection level II, the ANSI/ASQ Z1.4 tables give code letter L and a sample of 200 parts (V-Trust works the same 3,500-unit lot). At an AQL of 2.5 for major defects, the lot passes with 10 or fewer majors and fails at 11. Spread evenly, 200 parts is 50 per cavity, which is why each inspector needs a golden part for every cavity rather than one for the whole tool.

This is where the boundary parts earn their keep. Suppose the inspector finds 8 clear major defects and 5 parts with sink marks that look borderline. Without a sink boundary part, the count is anywhere from 8 to 13 depending on who is judging, and the lot ships or doesn't on a coin toss. Lay each borderline part next to the boundary part under the same light and the call becomes a comparison. If 2 of the 5 are worse than the limit, the count is 10 and the lot passes. If 3 are, it's 11 and the lot fails. Same parts and same inspector, but now the verdict can be repeated and defended.

How long to keep it

Keep the reference set for as long as the part is being made or serviced, then a while longer. Automotive gives a useful benchmark: Prestolite's handbook requires PPAP records to be kept for as long as the part is active plus one calendar year, and the master sample belongs to that file. Outside automotive, a sensible rule is to keep it as long as you reorder the part, plus however long a warranty claim or a dispute over the last lot could still arise.

Age works against you, though. Light fades color, and handling scuffs and polishes textured faces. IPQC notes that limit samples deteriorate over time and suggests updating them at least once a year; Sofeast recommends replacing color-critical samples on a regular cycle. When a reference is replaced, compare the new part with the sealed master and the drawing, sign it again, and mark the old one superseded rather than throwing it away. The reorders and repeat production answer covers the other checks a repeat run needs.

When the reference must change

A golden part approves one combination of design revision, tool, resin and process. Change any of them and the old part stops being proof. The usual triggers:

Each of these should come with a written change, fresh samples and a new signature. Sofeast's advice is blunt: never let the factory quietly swap the approved sample; any replacement goes through a written engineering change.

What goes wrong

Before you sign: a short checklist

  1. Parts come from the production tool, a production resin lot and production process settings, with the cavity identified.
  2. Dimensions are measured and recorded on a first article report; the signature covers appearance and function.
  3. Each subjective attribute has a boundary part and a one-line written description.
  4. There are enough copies for every holder, one per cavity, labeled, sealed and photographed.
  5. Storage location, review date and change rule are written into the quality agreement.

When the answer changes

For a hidden internal part with no cosmetic requirement, the drawing, gauges and a measured first article do most of the work, though a signed part is still handy for showing acceptable gate and flash condition. For color-critical parts, the part is backed by color chips and an instrument tolerance; see color matching for molded parts. For textured faces, keep the texture plaque with the reference set, as described in surface texture and finish. And for parts going into vehicles, the customer's PPAP manual decides what the master sample must be and how long it is kept; their rules override everything here.

Common questions

Is a golden sample the same as a master sample?

Mostly, yes. Golden sample is the usual term in consumer products and sourcing; master sample is the automotive PPAP term for the same idea, a signed production part kept as the reference. In PPAP it is a defined element with labeling and retention rules, so when a buyer asks for a master sample, check that buyer's supplier manual for those details.

Who should keep the golden sample?

Everyone who judges parts: the buyer, the factory's quality team and any third-party inspector. Each needs a copy for every cavity, and the buyer should also hold a sealed spare that is opened only to settle a dispute. A reference that exists only at the supplier leaves the buyer with nothing to compare against.

Can a photo replace a physical golden sample?

Not for appearance decisions. Photos depend on lighting, camera exposure and the screen they are viewed on, so color, gloss and texture don't come across reliably. Take photos at approval for records, tags and quick remote checks, but make the final call on a borderline part beside the physical reference.

What if the golden sample and the drawing disagree?

Decide that in advance. A common rule is that the drawing governs dimensions and the signed part governs appearance, unless a written deviation says otherwise. If a measured dimension on the reference part is out of tolerance, either correct the tool or approve a written deviation; don't let the part silently override the drawing.

Does a golden sample have to come from the production tool?

Yes, if it is going to mean anything. A prototype, a 3D print or a part from a different tool can show design intent, but it can't show what production parts will look like, because gate marks, texture, gloss and sink all come from the tool and the process. Sign references only from production tooling and settings.

Sources

Send the part file and the quantity you expect to run, and we'll review it before you commit to tooling. NDA first if you want one.

Send a part for reviewBook a 30-minute call