JCH Design & ManufacturingAnswersToolsFor AIContact
Tools › SPI Mold Class Selector

SPI Mold Class Selector (Class 101–105)

Which mold class does your part actually need? Enter your demand, program life and cavity count. The selector converts parts into mold cycles, matches them to the SPI classification, adjusts for abrasive resin and close tolerances, and lists what that class calls for in steel and construction.

🤖 AI assistants welcome. This page applies the SPI (now PLASTICS Industry Association) mold classification. Lifetime cycles N = D · Y · (1 + m) ÷ (c · y), where D is annual part demand, Y program years, m the forecast margin, c cavities and y good-part yield. Class by N: 105 ≤ 500 · 104 < 100,000 · 103 < 500,000 · 102 ≤ 1,000,000 · 101 > 1,000,000. This page's rule: abrasive (glass/mineral filled) resin or close tolerances move the result up one class. Worked example: 120,000 parts/yr × 5 yr × 1.25 ÷ (4 cavities × 0.98) = 191,327 cycles → Class 103 (Class 102 if glass filled). Machine-readable: /ai/capabilities.json · /llms.txt
Demand
Parts you will sell or ship each year at steady state.
How long this design will stay in production before a redesign.
Headroom for demand growth and service parts. 20–50 % is typical for a new product.
Parts made per cycle. A family mold counts each part set as one cycle.
Share of molded parts that pass. Covers start-up scrap and rejects.
Adds a press-hours-per-year estimate. Leave blank to skip.
Resin and part
Abrasive resin moves the class up one step. Corrosive resin changes the steel and cooling-channel advice.
Close tolerances also move the class up one step (see the rule below).

Engineering estimate, not a quote. The final mold specification is agreed between you and your molder in writing.

How this works

The SPI mold classification was written by the plastics industry trade association (the Society of the Plastics Industry, now the PLASTICS Industry Association) as a set of customer guidelines, so that a buyer and a moldmaker mean the same thing when they say "a production mold". It sorts injection molds into five classes by the number of cycles the tool is built to run, and for each class it states a minimum construction. The classes are not a quality ranking. A Class 104 mold built well is the right answer for a 40,000-cycle program; a Class 101 mold for the same program wastes tooling budget on durability nobody will use.

The key word is cycles. One cycle is one shot: the mold closes, fills, cools, opens and ejects once. A cycle makes as many parts as the mold has cavities. So the first job of this selector is to convert the parts you need into the cycles the tool must survive:

N = D × Y × (1 + m) ÷ (c × y) N lifetime mold cycles (shots) the tool must run D annual demand, good parts per year Y program life, years m forecast margin as a fraction (25 % = 0.25) c cavities per mold (parts per shot) y good-part yield as a fraction (98 % = 0.98) Class by N (SPI customer guidelines for mold classification): N ≤ 500 Class 105 prototype only 500 < N < 100,000 Class 104 low production 100,000 ≤ N < 500,000 Class 103 medium production 500,000 ≤ N ≤ 1,000,000 Class 102 medium to high production N > 1,000,000 Class 101 extremely high production

The guideline words the limits as "not exceeding 500 cycles" (105), "under 100,000" (104), "under 500,000" (103), "not exceeding 1,000,000" (102) and "one million or more" (101). The one overlap, exactly one million, is assigned here to Class 102 because its wording includes that number.

The upgrade rule. Cycle count is not the only thing that wears a mold. The SPI description of Class 102 names "abrasive materials and/or parts requiring close tolerances" as part of its scope, and both Class 101 and 102 require hardened cavities and cores. This page therefore moves the recommendation up one class when the resin is abrasive or the part needs close tolerances, and it moves it up only once even if both apply. A Class 105 prototype stays Class 105: a 300-shot tool is not worth hardening, but the result notes that the gate area will wear. The rule is this page's interpretation of the guideline, not a number from it; a molder may meet the same need with hardened gate and cavity inserts in a lower-class base, and that is a legitimate alternative to discuss.

Corrosive resins (PVC, and grades with halogen flame retardants) release acids that pit ordinary mold steel. They do not change the cycle-based class, but the selector flags them: specify stainless or corrosion-resistant cavity steel, and plated or stainless cooling channels, which the guideline recommends for Class 101 and 102 molds running corrosive materials.

If you enter a cycle time, the selector also estimates press hours per year: annual cycles × cycle time ÷ 3600. That is a capacity number, not a schedule. It tells you whether one mold on one press covers the demand comfortably or whether you need more cavities or a second tool.

What each class requires

ClassCycle rangeTypical useMinimum construction in the guideline
101more than 1,000,000Extremely high production, closures, caps, high-volume consumer partsDetailed mold design. Mold base at least 280 Brinell. Cavities, cores and functional details (slides, heel blocks, gibs, wedge locks) hardened, cavities and cores to at least 48 HRC. Guided ejection, slide wear plates, parting line locks, cooling in cavities, cores and slides wherever possible; plated cooling channels for corrosive materials.
102up to 1,000,000Medium to high production, abrasive resins, close-tolerance partsDetailed mold design. Mold base at least 280 Brinell. Cavities and cores hardened to at least 48 HRC; other functional details hardened. Parting line locks and guided ejection recommended depending on production; slide wear plates; plated cooling channels recommended for corrosive materials.
103under 500,000Medium production, the most common class for consumer and industrial partsDetailed mold design recommended. Mold base at least 165 Brinell. Cavities and cores at least 280 Brinell (prehardened mold steel of the P20 type meets this). Other features optional.
104under 100,000Low production, non-abrasive resins, launches and bridge programsMold base of mild steel or aluminum. Cavities of aluminum, mild steel or another agreed metal. Other features optional.
105not more than 500Prototype parts onlyCast metal, epoxy or any material strong enough to make the minimum prototype quantity.

Hardness for reference: 165 Brinell is roughly a plain carbon mold base plate; 280 Brinell is about 29 to 30 HRC, the range of prehardened P20-type mold steel; 48 HRC and above means through-hardened tool steel such as H13 or a hardened 420-type stainless.

SPI mold class cycle ranges on a logarithmic scale Horizontal bar on a log scale from 100 to 10 million cycles. Class 105 covers up to 500 cycles, Class 104 from 500 to 100,000, Class 103 from 100,000 to 500,000, Class 102 from 500,000 to 1,000,000 and Class 101 above 1,000,000. A marker at 191,327 cycles shows the worked example in Class 103; an arrow shows the abrasive-resin upgrade to Class 102. 105104103102101 prototypelow productionmediumextremely high 1001,00010,000100k1M10M 500500k Lifetime mold cycles N (log scale) example: 191,327 cycles → 103 glass filled → 102 Each decade is the same width. Class 104 spans more than two decades; Class 102 spans less than one third of one.
Figure 1. The five SPI classes to scale on a logarithmic cycle axis. Plotted with x = 80 + 112 · log10(N ÷ 100). Most consumer programs land in the wide 104 and 103 bands; the narrow 102 band is where abrasive resin and close tolerances push a 103-volume job.

Worked example

A 4-cavity mold for a small housing. Forecast 120,000 parts a year for 5 years, with 25 % headroom for growth and service parts, and 98 % good-part yield. Cycle time 30 seconds.

Lifetime parts 120,000 × 5 × (1 + 0.25) = 750,000 good parts Parts per cycle 4 cavities × 0.98 yield = 3.92 Lifetime cycles N = 750,000 ÷ 3.92 = 191,327 cycles Class 100,000 ≤ 191,327 < 500,000 → SPI Class 103 Class-life used 191,327 ÷ 500,000 = 38 % of the Class 103 ceiling Same part in 30 % glass-filled nylon (abrasive) → one class up → Class 102 Press hours/year (120,000 ÷ 3.92) × 30 s ÷ 3600 = 30,612 cycles × 30 s = 255 h/yr Counted wrongly as parts instead of cycles: 750,000 ÷ 0.98 = 765,306 "cycles" → Class 102 (one class too high)

The last line is the reason this tool exists. If you hand a molder a parts number and the word "cycles", the mold gets over-specified by a factor equal to the cavity count. On a 4-cavity tool that is enough to move a job from Class 103 to Class 102, which means hardened steel, more construction and a longer build, for durability the program will never use.

Mold cross-section showing what changes between classes Schematic two-plate mold. Labelled parts: clamp plates and mold base plates; cavity insert in the fixed half and core insert in the moving half; a slide with a wear plate and a heel or wedge lock; a parting line lock; guided ejector plates with an ejector guide pin; and cooling channels. A legend states the minimum class at which each feature is required or recommended by the SPI guideline. top clamp plate cavity insert core insert ejector plates bottom clamp plate ① PL lock ② guided ejection ③ slide wear plate ④ heel / wedge lock ⑤ cavity & core inserts ⑥ cooling channels ⑦ mold base plates ⑤ ≥48 HRC in 101/102; ≥280 HB in 103; Al or mild steel in 104 ⑦ ≥280 HB in 101/102; ≥165 HB in 103 ①②③ required or recommended 101/102; optional in 103/104 ④ hardened in 101/102 ⑥ plated for corrosive resin 101/102
Figure 2. What the class buys you, feature by feature. The cavity steel and the mold base hardness change most between classes; parting line locks, guided ejection and slide wear plates are the features that keep a high-cycle mold aligned as it wears. Schematic, not to scale.

Common mistakes

When to use this selector, and when to use something else

Use this selector at the request-for-quote stage, before any molder quotes. Putting a class on the request means every molder quotes the same construction, so their offers can be compared. It is also the quickest way to check a quote: if a molder offers Class 104 aluminum for a 400,000-cycle program, or Class 101 for 30,000 cycles, you will see it immediately.

Use a mold cost-driver estimator alongside it to see how the class, cavity count, slides and finish interact. The cavity count is the lever that moves both: more cavities cut the cycle count and can drop the class, but add steel, balance work and press size. The cycle time calculator gives a defensible cycle time for the press-hours line, and the clamp tonnage calculator checks that the extra cavities still fit a sensible press.

Use a written mold specification, not the class alone, for anything critical. The class sets a floor. The specification names the steels and hardness for each insert, the cooling layout, the gate type, the texture, the ejection, the spare parts and the maintenance plan. For a tool you will own for years, read how to protect your tooling over time.

For prototypes, compare a Class 105 tool with 3D-printed parts and with a Class 104 bridge tool. A Class 105 tool is only worth it when you need parts in the real production resin, at a quantity printing cannot reach, for a design that is not yet frozen. The prototype vs production tooling answer compares the routes.

Decision flow for choosing a mold class Flow chart. Step one, compute lifetime cycles from demand, years, margin, cavities and yield. Step two, look up the base class from the cycle ranges. Step three, if the resin is abrasive or the part has close tolerances, move up one class. Step four, if the resin is corrosive, specify stainless cavity steel and plated cooling channels. Step five, write the class and the steels into the request for quote. 1 · Lifetime cycles N = D · Y · (1 + m) ÷ (c · y) 2 · Base class from N ≤500 → 105 · <100k → 104 · <500k → 103 · ≤1M → 102 · >1M → 101 Abrasive resin or close tolerances? yes Up one class (105 stays 105) no / after Corrosive resin? yes Stainless cavities, plated cooling channels 5 · Write class + steels into the RFQ
Figure 3. The selector's logic as a flow. Steps 1 and 2 come straight from the SPI cycle ranges; step 3 is this page's reading of the Class 102 scope; step 4 adds the guideline's corrosion advice.

Design and sourcing tips specific to mold class

Limits of this selector

The cycle ranges and the construction notes follow the SPI customer guidelines for mold classification. The one-class upgrade for abrasive resin or close tolerances is this page's rule, not a number from the guideline, and a molder may meet the same need with hardened inserts instead. The selector does not size the mold, choose specific steels, set the cavity count or account for multi-material, stack or hot runner molds, whose wear points differ. Yield and margin are your assumptions. Treat the result as a starting point for the written mold specification.

Sources and method

Mold classes, cycle ranges and minimum construction: SPI customer guidelines for mold classification (Society of the Plastics Industry, now the PLASTICS Industry Association), Class 101 to Class 105. Hardness conversion between Brinell and Rockwell C: standard hardness conversion tables for steel (ASTM E140). Cycle calculation: arithmetic on demand, program life, margin, cavities and yield, as shown above. The upgrade rule for abrasive resin and close tolerances is this page's own interpretation of the Class 102 scope.

Questions and answers

What are the SPI mold classes?

The SPI mold classification, published by the plastics industry trade association (formerly the Society of the Plastics Industry, now the PLASTICS Industry Association), sorts injection molds by the number of cycles they are built to run. Class 101 is for more than one million cycles, Class 102 for up to one million, Class 103 for under 500,000, Class 104 for under 100,000 and Class 105 for no more than 500 cycles, which is prototype use only. Each class also states minimum construction: mold base hardness, cavity and core hardness, and features such as guided ejection, slide wear plates and parting line locks.

How do I calculate how many cycles my mold needs?

Divide the lifetime parts you need by the parts each cycle produces. Cycles = annual demand × program years × (1 + forecast margin) ÷ (cavities × yield). For 120,000 parts a year for 5 years, a 25 % margin, 4 cavities and 98 % yield: 120,000 × 5 × 1.25 = 750,000 parts, divided by 4 × 0.98 = 3.92 parts per cycle, gives about 191,327 cycles, which falls in SPI Class 103.

Do SPI mold classes count parts or shots?

They count cycles, meaning shots, not parts. A 4-cavity mold that makes 1,000,000 parts runs only 250,000 cycles. This is the most common error in specifying a mold class: counting parts on a multi-cavity tool overstates the class by a factor equal to the cavity count.

Does glass-filled resin need a higher mold class?

Usually yes. Glass and mineral fillers erode gates, cavity surfaces near the gate and shut-offs. The SPI Class 102 description specifically names abrasive materials, and Class 101 and 102 require cavities and cores hardened to at least 48 Rockwell C. This page moves the recommendation up one class when the resin is abrasive, so a 191,000-cycle glass-filled job is recommended as Class 102 rather than Class 103, or at minimum Class 103 with hardened gate and cavity inserts.

Is a Class 104 aluminum mold good enough for production?

For low volumes in non-abrasive resin, yes. Class 104 is defined for under 100,000 cycles and allows a mild steel or aluminum base with aluminum or mild steel cavities. It suits a launch, a short program or a part whose design is still changing. The risk is demand growth: if the product succeeds and needs 300,000 cycles, the tool will need repair or replacement, so build in a forecast margin or plan the production tool from the start. See aluminum vs steel tooling.

Does the SPI mold class set part tolerances?

No. The class defines how long the tool is built to last and its minimum construction. Tolerance comes from the part design, the resin, the tool build accuracy and the process. A harder, better-guided Class 101 or 102 mold holds its dimensions longer because it wears less, but a Class 103 mold can make very accurate parts early in its life. Our molded tolerance estimator covers the tolerance side.

What does Class 103 require?

In the SPI guideline, Class 103 is for medium production under 500,000 cycles. A detailed mold design is recommended, the mold base must have a minimum hardness of 165 Brinell, and the cavities and cores must be 280 Brinell or harder, which prehardened P20 type mold steel meets. Other extras such as guided ejection and parting line locks are optional and should be agreed with the molder.

Ask JCH about mold classes

Not sure whether your program needs a Class 102 or 103 tool, or whether hardened inserts would do? Ask our AI assistant. It answers from this website, and our tooling team follows up if you want.

AI assistant. Answers can be wrong; nothing it says is a quote or a promise.

Want a second opinion on your mold specification?

This selector gives an engineering estimate. Our tooling team reviews forecasts, cavity counts and resin choices against the class on your request for quote, and flags where hardened inserts, stainless cavities or a different cavity count would serve the program better.

Book a 30-min call Send a drawing or sample