Answers › IML and IMD

What are in-mold labeling (IML) and in-mold decoration (IMD)?

Reviewed by the JCH tooling team · Updated

In-mold labeling (IML) and in-mold decoration (IMD) put a printed label or film inside the mold before the shot, so the graphic is molded into the part instead of printed on afterwards. The decoration survives abrasion and cleaners far better than surface ink, but the tooling, film and artwork are fixed, so it pays at volume.

Three different things share these names

Before comparing quotes, pin down which process is meant, because suppliers use the terms differently. One technical reference calls a back-molded, formed film "IMD" and a flat packaging label "IML". A film maker uses "IMD" for a transfer process where the carrier is peeled away and "IML" for any film that stays on the part. Both are describing real processes; they just draw the line in different places.

Flat in-mold label (packaging IML)Film insert molding (often called IMD or FIM)Transfer IMD (in-mold transfer)
What goes in the moldA flat or wrapped printed label, usually polypropyleneA printed, usually pre-formed clear filmA carrier foil fed across the mold, carrying the ink layers
What stays on the partThe whole labelThe whole film, which becomes the outer skinOnly the ink and coating layers; the carrier is removed
Typical resinPP or PE, matched to the labelPC, PC/ABS, ABS, PMMAMatched to the transfer layer by the foil supplier
Typical partsTubs, lids, pails, cupsAppliance fascias, device housings, automotive trim, control panelsThin decorated housings, wood- or fabric-look panels
Where the graphic sitsOn the label surface, under its own coatingBehind the clear film, protected by its thicknessOn the surface, under a thin protective coat

Ask the supplier to describe which layer ends up on the outside of the part. That one answer tells you which process they mean and how the decoration will wear.

How film insert molding builds the surface

A film for insert molding is a stack, and each layer has a job. Scott Sabreen's engineering summary lays it out: a clear carrier film, polycarbonate at 125 to 500 µm being the default; a hardcoat of about 3 to 10 µm on the outside for scratch and chemical resistance; the graphics printed on the back of the film (second-surface printing), often with a backing color and a light-block layer for backlit icons; and a tie layer matched to the resin that will be molded behind it. Polycarbonate film bonds directly to PC and PC/ABS, while ABS and PMMA usually need the tie layer.

The route runs print, dry, die-cut, form, trim, load, mold. Forming is done either by thermoforming above the film's glass transition or by high-pressure forming below it at 100 to 300 bar, which holds registration and tight radii better. The formed film sits against the cavity wall and resin is shot in behind it.

Cross-section of a film insert molded part: printed film against the cavity wall, resin injected from a gate on the back side away from the print cavity steel (the show side of the part) back-molded resin (e.g. PC or PC/ABS) gate keep the gate 10 to 15 mm or more clear of any print Layers, outside in: hardcoat (3 to 10 µm) clear carrier film (125 to 500 µm) ink printed on the back (second surface) tie layer bonding film to resin

Because the ink sits behind the film, abrasion attacks the hardcoat, not the artwork. The failure that matters in service is almost always the bond between film and resin.

What the tooling needs

An open injection mold in a press with a bright green molded crate held on the moving half, blue mold plates and tie bars around it.
A large crate on the moving half of an open mold. Molded packaging is the home of flat in-mold labels, with tubs, lids and pails the classic examples: a robot places the label on the cavity wall before the mold closes, so the part comes out already decorated.

Worked example: a decorated control panel

Take a hypothetical PC/ABS control panel, 180 by 60 mm, with a 12 mm draw at the edges, 1.0 mm corner radii, and a printed 1.0 mm frame around a display window.

  1. Draw and radius. A 12 mm draw is inside the roughly 30 mm limit Sabreen gives for thermoformed film. The 1.0 mm radius is not: thermoformed film wants about 2 to 3 mm. Either open the radii to 2.5 mm or plan on high-pressure forming, which reaches 0.5 to 1 mm. Film also thins at corners, so keep graphics off them.
  2. Registration. Expect about ±0.5 mm on thermoformed film and ±0.1 to 0.3 mm on high-pressure formed film. With a 1.0 mm frame, ±0.5 mm could shift it by half its width, so high-pressure forming is the safer choice here, with the artwork pre-distorted for forming stretch and the blank located on formed features rather than on the print.
  3. Gate. Put a fan gate on the back face under an unprinted zone at least 15 mm from the window frame.
  4. Bond and process. PC film bonds directly to PC/ABS. Dry the film 2 to 4 hours at 80 to 100 °C so absorbed moisture doesn't become bubbles, and run the mold in the 60 to 90 °C window for PC/ABS.
  5. Proof. Specify a cross-hatch adhesion test (ASTM D3359 Method B, with 4B to 5B as typical acceptance), a Taber abrasion test (ASTM D4060), and soaks in whatever the panel will meet in use, then repeat adhesion after the soaks.

What goes wrong

SymptomUsual causeUsual fix
Ink washed out near the gateGate too close to print, melt too hot or too fastMove or fan the gate, slow the fill past the art, lower melt temperature
Bubbles or film liftingMoisture in the film, wrong tie layer, cold moldDry the film, match the tie layer to the resin, raise mold temperature
WrinklesDraw too deep for the radius, uneven film heatingOpen the radius, re-profile heating, or switch to high-pressure forming
Graphic out of positionNo pre-distortion, film lot shrinkage, locating on the printPre-distort artwork, control film storage, locate on formed features
Label curl (packaging IML)Moisture or temperature imbalance in the label, static lost before fillCondition labels, re-time the static charge

When it beats printing after molding

In-mold decoration trades flexibility for durability and volume. The film or label is fixed artwork: no serial numbers, and every art change means new film. Pad printing, screen printing and hot stamping cost less to set up and suit shorter runs, though the ink stays on the surface; those methods are compared in pad printing, silk-screen and labels. In-mold wins when a graphic has to survive years of fingers and cleaners, when backlit icons and dead-front displays are needed, when a container must come off the press already labeled, or when a surface needs a look that paint or texture can't give. For texture-only finishes, mold surface texture is usually simpler; for parts that need a second material rather than a graphic, see two-shot molding. Enclosures that combine a decorated face with electronics behind it are covered in plastic and electronics enclosures.

What to send when asking for a quote

Common questions

What is the difference between IML and IMD?

It depends on who is speaking. In packaging, IML usually means a flat printed label molded onto a tub or lid, and IMD means a formed, printed film back-molded into a durable part. Some film makers use IMD for transfer decoration where the carrier film is removed. Ask which layer ends up on the outside of the finished part.

How durable is in-mold decoration?

Very durable when the film and resin are matched. On film insert molded parts the ink sits behind the film, so wear attacks the hardcoat, not the graphic. The weak point is the bond between film and resin, which is why adhesion should be tested after chemical and heat exposure, not just on fresh parts.

Can in-mold labels be recycled with the container?

Packaging labels are usually made from the same polymer family as the container, commonly polypropylene on a polypropylene tub, so the labeled container can be handled as a single material. Check the specific label construction and inks with the label supplier if recyclability claims matter for your packaging.

Does in-mold decoration need a special mold?

Usually yes. The tool needs a way to hold the label or film, typically static charge, vacuum or locating pins, a gate positioned on the back side away from printed areas, venting where film meets resin, and a cavity shaped around the formed film. Packaging IML also needs a labeling robot integrated with the press.

Can I change the artwork on an in-mold decorated part?

Yes, but every change means new printed film or labels, and if the change moves graphics near the gate, formed edges or corners, it may need forming or tooling adjustments too. Variable data such as serial numbers can't be printed in-mold; those are usually added afterwards by laser marking or inkjet.

Sources

Send the part file and the quantity you expect to run, and we'll review it before you commit to tooling. NDA first if you want one.

Send a part for reviewBook a 30-minute call