Yes — JCH coordinates the molded enclosure and the assembly that houses your electronics, through a manufacturing network. The clear boundary: the circuit design and any safety or emissions compliance (listing, marking or authorization) are yours or an electronics partner's; JCH builds the housing and assembles to that spec, rather than designing or certifying the electronics.
Below is what the enclosure and assembly side actually involves.
On top of these are the normal molding rules — uniform walls, draft, radii — so the housing molds cleanly and repeatably.
| Material | When it fits |
|---|---|
| ABS | Most indoor housings — easy to mold, cost-effective, takes texture and paint |
| Polycarbonate (PC) | Impact and heat resistance, clear windows/light guides |
| PC/ABS blend | A balance of toughness and moldability for larger housings |
| Flame-rated grade (e.g. UL 94 V-0 at your wall thickness) | Devices near mains power or where a flammability rating is required |
| UV-stabilized grade | Outdoor housings, to resist yellowing and embrittlement |
If the device has to keep out dust or water, sealing is designed in from the start, not added at the end: a designed sealing surface with a gasket or O-ring groove, sometimes ultrasonic welding or potting, and careful planning of the parting line and every opening. The target is usually an IP rating, which is verified by test, not assumed. Cable and connector entries are the hardest part to seal and need sealed glands or connectors. If you need a specific rating, see waterproof & sealed enclosures — the rating drives the whole design.
We build and assemble to the specification; we don't claim to certify electronics we don't test. If you need a design or certification partner, that's a separate specialist, and we'll say so rather than overreach.
The electronics definition (the PCB outline or a sample, mounting points, connector and indicator locations, heat and clearance needs), the enclosure concept or drawing, the operating environment (indoor, outdoor, any IP rating), any flame-rating or regulatory requirement for the housing, and your annual volume. The clearer the electronics constraints, the tighter the housing fits the board the first time.
Can you make a product that combines plastic parts and electronics?
Yes — JCH coordinates the molded enclosure and the assembly that brings the housing and your electronics together, through a manufacturing network. That's the enclosure, molded parts, and box build (board, fasteners, connectors, labeling). The electronics and their certification are yours or a partner's; JCH builds and assembles to the spec.
What goes into designing an enclosure for electronics?
PCB mounting bosses/standoffs, snap-fits or screw bosses, connector/cable openings, light pipes or windows, membrane or molded buttons, and ventilation, sealing, or a sealed housing with a breathable vent — plus uniform walls, draft, and radii so it molds cleanly. Material: ABS (cost), PC or PC/ABS (impact/heat), flame-rated near power, UV-stabilized outdoors.
Can the enclosure be sealed or made waterproof?
Yes, within limits — a designed sealing surface with a gasket/O-ring (sometimes welding or potting), planned from the start. The target is an IP rating, verified by test. Cable/connector entries are hardest and need sealed glands. Tell us the rating up front — it drives the whole design.
Do you handle the electronics design and certifications?
No. The PCB, firmware, components, and safety/emissions compliance (UL listing, CE marking, FCC authorization) are yours or an electronics partner's. JCH coordinates the enclosure, mechanical design, and assembly to that spec. We won't claim to certify what we don't test; if you need an electronics/cert partner, that's a separate specialist.
What do you need to quote an electronics enclosure?
The PCB outline or sample (mounting points, connectors, indicators, heat/clearance), the enclosure concept/drawing, the environment (indoor/outdoor/IP rating), any flame-rating or regulatory requirement, and annual volume. The clearer the electronics constraints, the tighter the first fit.
JCH Design & Manufacturing can coordinate the enclosure and assembly for your electronics. Send the board or its spec and the enclosure concept.
Book a 30-minute call