Answers › Recycled PCR resin

Can I use recycled (PCR) plastic in injection-molded parts?

Reviewed by the JCH tooling team · Updated

Yes, for many opaque parts, if you design and specify for it. Post-consumer resin varies more from lot to lot than virgin: melt flow can swing widely, color runs gray or yellow, and toughness drops. Blend it with virgin at a fixed ratio, write melt-flow and contamination limits into the spec, and qualify several lots before tooling is final.

First, get the words straight

"Recycled" covers several different materials, and they behave differently in a mold. Mixing them up is how a program ends up with the wrong expectations on cost, color and consistency.

TermWhat it isHow it behaves
Regrind / reworkYour own runners and rejects, ground and fed back into the same processKnown resin, one extra heat history. Not a recycled-content claim under the FTC Green Guides, because it never left the process.
Post-industrial (PIR, pre-consumer)Scrap or off-spec product from another manufacturer that never reached a consumerUsually one resin family, fairly clean, but its origin and additives may be unknown to you
Post-consumer (PCR)Products that were used, collected, sorted, washed and re-pelletizedMixed history, mixed additives, the most lot-to-lot variation and the strongest sustainability claim

The marketing side matters as much as the molding side. Under 16 CFR 260.13, a recycled-content claim has to be backed by material diverted from the waste stream, either during manufacturing (pre-consumer) or after consumer use (post-consumer). The FTC's own example is a manufacturer who mixes its spills and scraps back into the same product: calling that recycled content is deceptive, because that scrap would have been reused anyway. Where a claim distinguishes post-consumer from pre-consumer content, the regulation says the marketer should have substantiation for the stated percentage, and a product that is only partly recycled should have its claim qualified by the amount or percentage, by weight, of recycled content in the finished product. That's the regulation's wording; how your own label should read is a question for your counsel.

Why PCR molds differently from virgin resin

Virgin resin is made to a narrow specification. PCR is assembled from whatever came through the collection and sorting system, so three things change.

Viscosity moves around. Melt flow index (MFI) is the quick check of how easily a resin flows. One mold builder that runs PCR closures reports seeing MFI from 30 to 70 within the same batch of PCR, a spread that no virgin grade would ship with. On a fixed, conventional process, a setup made on a 50-MFI sample can flash with a 70-MFI lot and short-shot with a 30-MFI lot.

Melt flow of ten resin lots: virgin lots sit in a narrow band, PCR lots scatter from 30 to 70, and only some fall inside the process window the mold was set up for Melt flow by lot: virgin vs. post-consumer feed MFI 70 50 30 process window set at sampling virgin lots PCR lots (30 to 70 seen in one batch) lot number → Above the window: flash, overpacking. Below it: short shots, sink.

It has already been cooked. Every melt cycle oxidizes the polymer a little. PCR has been through at least two: making the original product and re-pelletizing. Materials labs list the results as lower molecular weight, more brittleness, lower strength and toughness, discoloration, loss of gloss and transparency, and odor from volatiles.

It carries other people's ingredients. PCR can contain plasticizers, fillers and lubricants from its first life, plus stray polymers the sorter missed. A contaminant that melts at a different temperature than the base resin can cause filling problems and extra scrap. Different polymers in one blend are often incompatible, which shows up as poor mechanical properties.

Where PCR fits and where it doesn't

PCR works best in opaque, darker-colored parts with generous walls and loose cosmetic and dimensional limits: bins, crates, brackets hidden inside an assembly, garden products, trays. It gets hard fast in these cases:

Open mold half on a molding machine with a white, circular swirl-vaned molded part still on the mold face
A white molded part still sitting on an opened mold half. The photo does not show which resin or feedstock the part is made from.

Worked example: a 30% PCR storage-bin lid

A hypothetical polypropylene lid weighs 180 g. Marketing wants "made with 30% post-consumer recycled plastic." Here's how the numbers carry through.

  1. Blend. The resin feed is 70% virgin PP and 30% PCR PP. Before color, that's 126 g virgin and 54 g PCR for every 180 g of resin. The part weight calculator gets you the shot weight from the CAD volume.
  2. Color dilutes the claim. The lid is gray, colored with masterbatch at 2% by weight of resin. A 180 g lid then holds 180 ÷ 1.02 = 176.5 g of resin, of which 52.9 g is PCR, so the PCR share of the finished part is 52.9 ÷ 180 = 29.4%. The Green Guides tie a partial claim to the percentage by weight in the finished product, so either raise the PCR fraction to about 30.6% of the resin (30.6 ÷ 102 = 30.0%) or state the lower figure. Small, but exactly the kind of gap an auditor checks.
  3. Viscosity window. If the PCR lots range from 30 to 70 MFI and the PCR is only 30% of the feed, the blended melt moves far less than the PCR alone does, but it still moves. The molder needs either a process that compensates (pressure-controlled filling, or adjusting settings by lot) or a PCR supplier who compounds lots together to narrow the spread.
  4. Lot qualification. Before tooling is final, ask for property data from several PCR lots; one failure-analysis lab suggests something like nine lots over a year to see the real range. Design the hinge and snap features for the bottom of that range, not the average.

What to put in the specification

How labs check incoming PCR

Melt flow is the fast screen at receiving. Differential scanning calorimetry (DSC) shows extra melting peaks that point to a second polymer, the classic case being polyethylene in a polypropylene stream, and it gives crystallinity data that helps set processing temperatures. Rheology across temperature and shear rate predicts how a lot will fill and whether it stays stable at processing temperature. For hygroscopic PCR grades, a moisture test before molding matters even more than with virgin resin, because regrind-like flakes and fines pick up water faster.

Decision checklist

  1. Which claim do you need: post-consumer, pre-consumer, or total recycled content? What percentage by weight of the finished part?
  2. Is the part opaque and a mid or dark color? If not, how will you handle the PCR's base color?
  3. Which features are tolerance-critical or load-bearing, and do they have margin for lower, more variable properties?
  4. Can the PCR supplier give multi-lot MFI and property data and lot traceability?
  5. Will the molder blend at a fixed ratio with metered dosing, and how will the process handle MFI changes between lots?
  6. Has the color standard been approved on parts made from the actual blend?
  7. Have first articles been tested at the low end of the PCR property range, not just on a good lot? Our page on samples and first articles covers what to ask for.

When the answer changes

If the goal is less waste rather than a printed claim, clean regrind of your own runners at a controlled percentage is often the simplest win, though it isn't a recycled-content claim. If the PCR supplier offers a compounded grade, blended and re-pelletized with stabilizers and sometimes extra antioxidant, much of the variability above shrinks, and higher PCR fractions become practical. And if the product is under a retailer or regional recycled-content rule, that rule's definitions and audit method govern, so get them in writing before tooling.

Common questions

What is the difference between PCR and regrind?

Regrind is your own runners and rejects, ground up and fed back into the same molding process, so it has a known history. PCR comes from products consumers used and threw away, collected and re-pelletized by a recycler. The FTC Green Guides' own example treats in-process scrap reused this way as not supporting a recycled-content claim; PCR does count as post-consumer content.

How much PCR can a molded part contain?

There is no single limit. Opaque, dark, thick-walled parts with loose tolerances can run high fractions, sometimes all PCR. Parts with tight tolerances, light colors or demanding toughness usually run a lower fraction blended with virgin. Qualify the fraction on parts molded from several PCR lots, not from one sample.

Does PCR change part dimensions?

It can. Melt flow varies more from lot to lot, which changes how fully the cavity packs, and that moves shrinkage and dimensions. Contaminants and different heat histories add more scatter. Expect to widen tolerances on non-critical features or narrow the PCR supply spec for critical ones.

Can recycled plastic be used for food-contact parts?

Only with a recycled grade that has the regulatory documentation for that specific food-contact use. Ordinary mechanically recycled PCR usually does not, because its prior contents and contaminants are unknown. Ask the resin supplier for the compliance letter that names the use, then confirm with your own regulatory review.

How do I prove a recycled-content claim?

Keep a paper trail from the PCR supplier's lot documents through receiving, blending records and finished-goods lots, and calculate the percentage by weight of the finished product, including colorant and other additives. The FTC Green Guides expect substantiation for any stated post-consumer or pre-consumer percentage.

Sources

Send the part file and the quantity you expect to run, and we'll review it before you commit to tooling. NDA first if you want one.

Send a part for reviewBook a 30-minute call