Answers › Coloring methods

Masterbatch, precolored compound or liquid color: how should molded parts be colored?

Reviewed by the JCH tooling team · Updated

Use masterbatch when one natural resin runs in several colors and the molder doses accurately, typically about 2 to 5%. Use precolored compound for tight brand colors, heavy pigment loads or short runs, since nothing is dosed at the press. Use liquid color for tints and low doses, if the molder runs it routinely.

Three ways the color gets in

Almost every colored molded part gets its color in one of three ways. The difference that matters most is where the mixing happens and who controls the dose.

Masterbatch (color concentrate)

Pellets packed with pigment in a carrier resin, metered into natural resin at the press. A trade article on coloring polymers puts typical let-down ratios at 20:1 to 50:1, natural resin to masterbatch, which is roughly 5% down to 2%. Colorant makers also offer concentrates designed for lower doses; one supplier case study cites 1 to 3% for a concentrate used across several different resins. The concentrates themselves are heavily loaded: in one colorant maker's molding catalog, many white masterbatches carry 60 or 70% titanium dioxide, and the blacks range from under 20% up to 60% carbon black.

Precolored compound

The resin maker or a compounder melts pigment into the resin on a compounding extruder, usually twin-screw for high pigment loads, and ships pellets that are already the final color. Nothing is dosed at the press. The color is fixed before the resin arrives.

Liquid color

Pigment dispersed in a liquid carrier, pumped into the feed throat from a drum or pail through a pickup lance. Liquid is commonly used for tinted clear and translucent parts and for opaque parts at let-down ratios under 2%, and it disperses well.

Where color enters the press: natural resin in the main hopper, masterbatch pellets metered by a doser or liquid color pumped at the feed throat, and the screw doing the mixing; precolored compound arrives already mixed and needs no doser Where the color goes in, and who does the mixing natural resin (or precolor) masterbatch doser liquid color pump feed throat to mold The screw is the only mixer for masterbatch and liquid color. Masterbatch: typically about 2 to 5% (50:1 to 20:1); some 1 to 3% Liquid: often under 2% for opaque parts Precolored compound: mixed on a compounding extruder before it ships

How to choose: what each method is good and bad at

MasterbatchPrecolored compoundLiquid color
Who controls the color doseThe molder's doser, every shotThe compounder, once per lotThe molder's pump, every shot
Typical doseabout 2 to 5%; some grades 1 to 3%none at the pressoften under 2%
Shot-to-shot consistencyGood with gravimetric dosing; drifts if pellets separate in the hopperBest; nothing to drift at the pressGood when the pump is maintained; stops without warning when the container runs dry
Hard colors and high pigment loadsCan be difficult or uneconomicBest fitPossible; screw slip risk at higher doses
Switching colorsEasy; one natural resin, several concentratesSeparate resin inventory per colorEasy, but purging and cleanup take care
Relative material costMiddleUsually highest per kilogram, but can win on short runs through less setup and scrapLowest colorant use per part
Shop-floor headachesDosing calibrationVery fewSpills, screw staining, shelf life, separation, cold-weather freezing

The precolored-on-short-runs point surprises people. A trade article on medical device coloring notes that precolored polymers can save setup time and raise part acceptance rates enough to save money on short runs, even though the pellets cost more. When a short run means a long tuning session at the press, the extra per-kilogram cost is often the cheaper option.

Open injection mold in a press with a bright green molded crate-type part on the moving half, tie bars visible
A part like this green crate is colored all the way through, not painted. Whether the green came from masterbatch, precolored pellets or liquid color decides how consistent it stays from one production lot to the next.

Worked example: what a 2% let-down really means at the press

A hypothetical two-cavity mold makes a 60 g part per cavity with an 8 g cold runner: 128 g per shot. The color is a mid-blue masterbatch specified at 2% of the total blend.

  1. Per shot: 128 g × 0.02 = 2.56 g of masterbatch. That's a small pinch of pellets per shot, which is why dosing accuracy matters so much.
  2. Per hour: at a 30 s cycle, 120 shots per hour, so 15.4 kg of blend and about 0.31 kg of masterbatch. (Check your own shot against barrel size with the shot size calculator.)
  3. Dry-blending a bag instead: for 2% of the total in a 25 kg bag of natural resin, add 25 × 0.02 ÷ 0.98 = 0.51 kg of masterbatch.
  4. Dosing error: a volumetric doser that drifts 10% off its setpoint puts 1.8 to 2.2% concentrate into the part, so the pigment in the part moves by the same 10%. That is the kind of variation that shows up as lot-to-lot shade differences, and gravimetric or loss-in-weight feeders exist to reduce it.
  5. Hopper separation: heavily loaded concentrates can be far denser than the natural resin (white masterbatches at 60% titanium dioxide are listed at about 1.7 g/cm³ in one colorant maker's catalog, well above most natural resins they go into), and pellets that differ in density and size can separate in a hopper under vibration. A pre-blended bag can feed color-rich at the start and color-lean at the end. Dosing right at the throat avoids most of this.

Now compare a precolored version of the same blue. There's no step 3, 4 or 5: every pellet carries the same color, and the variation comes down to the compounder's lot control, which is checked once per lot instead of once per shot. If the blue is a brand color under a tight ΔE limit and the run is modest, that's a strong argument for precolor. If the same part runs in six colors from one natural resin, masterbatch wins on inventory.

Things that go wrong, and why

Decision checklist

  1. How tight is the color tolerance, and is it a brand color customers will see side by side?
  2. How many colors does this part run in, and how often does the color change?
  3. How long are the runs? Short runs with tight color favor precolor; long runs in several colors favor masterbatch.
  4. Does the base resin carry a flame, food-contact or medical rating that limits which colorants can be used?
  5. Is the part clear or translucent? Liquid color or a dedicated tint concentrate is often the right tool.
  6. Does the molder dose gravimetrically at the throat, and is the let-down ratio written on the process sheet?
  7. Has the color been approved on molded parts in the production resin and texture, against a signed standard? The matching process itself is covered on our color matching page.

When the answer changes

If the part is going to be painted, printed or labeled anyway, the molded-in color may only need to be close, and the cheapest adequate method wins; pad printing and silk-screen decoration covers that route. If the order quantity is small, a precolored compound may come with its own minimum per color from the compounder, which can change the math; compare it against the run sizes discussed in minimum order quantities. And if material cost per part is the driver, the cost per part calculator shows how much the colorant actually adds compared with resin, cycle time and scrap.

Common questions

What is a let-down ratio?

It is how much color concentrate is mixed into natural resin. A 50:1 ratio means 50 parts natural resin to 1 part masterbatch, about 2%. Trade sources put typical masterbatch ratios at 20:1 to 50:1, roughly 5% to 2%, and some concentrates are made to run at 1 to 3%.

Is precolored resin more consistent than masterbatch?

Usually, yes. The pigment is compounded into every pellet before shipping, so nothing at the press can change the dose. Masterbatch depends on the molder's doser and on concentrate pellets not separating from the natural resin in the hopper. Good gravimetric dosing closes much of the gap.

Why is liquid color cheaper to use?

Liquid color typically runs at lower let-down ratios than pellet concentrates, often under 2% for opaque parts, so less colorant goes into each part. The savings can be offset by pump equipment, cleanup, shelf life and handling issues, which is why many molders standardize on pellets instead.

Can masterbatch affect part strength?

It can, especially at higher doses or with an incompatible carrier resin. The carrier resin dilutes the base resin. At typical doses with a compatible carrier the effect is usually small, but a load-bearing or rated part should be tested in its production color, not in natural.

Which coloring method should a first production run use?

It depends on the color tolerance and run size. For a single brand color with a tight tolerance and modest volume, precolored compound often gets to approved parts fastest. For a part that will run in several colors, masterbatch keeps one natural resin in stock. Approve color on molded parts either way.

Sources

Send the part file and the quantity you expect to run, and we'll review it before you commit to tooling. NDA first if you want one.

Send a part for reviewBook a 30-minute call