Certificate of conformance: what it should say, what it proves, and what it does not
Most purchase orders ask for a C of C with every shipment and never say what it must contain. Here is what a useful certificate says, where it stops, and why it is not the CPSC certificate an importer owes.
Filed under Line watch and quality control
Short answer: A certificate of conformance (CoC) is a signed statement from the supplier that a specific shipment meets your purchase order, drawing and specifications. It is a promise, not a test result. It is only worth as much as the requirements it points to and the records behind it, so tie it to a lot, a drawing revision and named reports, and keep the right to inspect. For consumer products imported into the US, a factory CoC does not replace the CPSC certificate the importer must issue.
Almost every purchase order we see asks for a "C of C with each shipment." Almost none of them say what it must contain. The factory then sends a one-paragraph letter that says the goods conform, with no lot number, no drawing revision and no reports attached. It satisfies the checkbox and proves very little. This note covers what a certificate of conformance actually is, what a useful one says, where it stops, and how it differs from the US consumer-product certificates that importers are legally required to issue.
What a certificate of conformance is
Wikipedia's entry, citing an American commerce definition, describes it as "a document certified by a competent authority that the supplied good or service meets the required specifications". The same entry adds the part that matters most to a buyer: "A certificate of conformance is a lot/datecode specific certification that provides traceability of the goods back to the point of manufacture."
That second sentence is the useful one. A CoC that is not tied to a lot or date code cannot be traced to anything. If parts fail in the field, you want to be able to pull the certificate for that lot, see which drawing revision it was built to, and see which inspection reports it relied on. A generic letter that would read the same for every shipment cannot do that.
The words vary. Buyers and factories use certificate of conformance, certificate of conformity and certificate of compliance loosely and often interchangeably in purchasing. In regulated contexts they are not interchangeable, as the US consumer-product rules below show. Read the requirement that names the document, not just the title on it.
What the US government's version shows
The clearest public model is the Federal Acquisition Regulation. Under FAR 46.504 a certificate of conformance "may be used in certain instances instead of source inspection", at the contracting officer's discretion, when acceptance on that basis is in the government's interest and either the risk of loss is small or the contractor's track record makes defects unlikely. The matching clause, FAR 52.246-15, says that once authorized in writing, "the Contractor shall ship with a Certificate of Conformance any supplies for which the contract would otherwise require inspection at source."
The certificate text the clause prescribes is a good template for any buyer. It names the date, the contractor, the contract number, the carrier and the shipping document, and then reads: "I further certify that the supplies or services are of the quality specified and conform in all respects with the contract requirements, including specifications, drawings, preservation, packaging, packing, marking requirements, and physical item identification (part number)", and that they are in the quantity shown on the acceptance document.
Two things in that clause are worth copying into commercial purchase orders. First, the certificate is tied to one shipment and one shipping document. Second, it does not end the buyer's rights. The clause keeps the right to inspect, and it says: "The Government has the right to reject defective supplies or services within a reasonable time after delivery by written notification to the Contractor." A CoC replaces some inspection on trust. It does not waive your remedies if the trust turns out to be misplaced.
What a useful CoC says
For a commercial program, ask for a certificate that carries at least:

- Supplier name and the site that made the goods. If the factory subcontracts a process, say whether the certificate covers it.
- Your purchase order number and line items, with part number and the drawing revision each part was built to.
- Lot, batch or date code, and quantity shipped, matching the cartons and the packing list.
- The requirements it certifies to: drawing, specification, material grade, finish, packaging and marking requirements. Name them; do not write "all applicable requirements."
- The evidence behind it: the inspection report, material certificate or test report numbers, with the documents attached or available on request.
- Any approved deviations, by deviation or concession number. A CoC that hides an accepted deviation is a false certificate.
- A named signer with a title and a date.
Items 4 and 5 are where most certificates fall short. A statement that goods "conform to the order" is only as specific as the order. If the drawing on file is two revisions old, the CoC certifies the wrong part. This is one reason we treat drawing control and the engineering change order process as part of quality, not paperwork.
Where a CoC stops
A CoC is a statement by the party being paid. It is useful because it puts a name and a signature on a claim, and it gives you a document to point to if the claim is false. It is not independent evidence. On a new supplier, a new part or a changed process, verify before you rely on it:
- New parts and changes: run a first article inspection and approve it before production. The CoC on later lots can then point to the approved first article.
- Each lot, until the supplier has earned trust: a pre-shipment inspection on a sample drawn by your own inspector, with an agreed sampling plan.
- Materials: ask for the resin, metal or fabric supplier's certificate behind the factory's own, so the chain reaches the material maker.
The FAR treats a CoC the same way: something that may stand in for source inspection when the risk is low or the supplier's record is good, not by default. That is a sensible rule for any buyer. Earn the reduced inspection; do not start with it.
Not the same as a CPSC certificate
For consumer products sold in the United States, there is a separate, legal certificate, and a factory CoC does not satisfy it. Under the Consumer Product Safety Commission's rule at 16 CFR part 1110, "There are two types of finished product certificates: Children's Product Certificates (CPCs) and General Certificates of Conformity (GCCs)." These certify that a finished product complies with the specific CPSC rules, bans, standards or regulations that apply to it.
For goods made outside the US, the rule says "the importer, as defined in this part, is the finished product certifier that must issue a finished product certificate that meets the requirements of this part." Certificates for such imported finished products "are required to be eFiled" in US Customs' ACE system at entry. The importer may rely on others for testing or data entry, but the certifier "remains legally responsible for the information in a finished product certificate, including its validity, accuracy, completeness, and availability." Records supporting the certificate must be kept "for at least five years from the certificate creation date".
Factories can still help. Under the same part, "component part certificates are voluntary, but may be relied upon by a finished product certifier to issue a finished product certificate." So a supplier's certificate for a component, backed by test records, can feed your GCC or CPC. But if your company is the importer of record, the finished product certificate is yours. If you are unsure whether your product falls under a CPSC rule, ask before the first shipment, not at the port; the CPSC publishes guidance for small businesses on its website.
What to put in the purchase order
The certificate is easiest to get right when it is specified before the order is placed. In the purchase order or quality agreement, write:

- that a CoC is required with each shipment and must reference the PO, part number, drawing revision, lot and quantity;
- which reports it must attach or reference (first article, final inspection, material certificates, any test reports);
- that approved deviations must be listed on it;
- that acceptance of a CoC does not waive your right to inspect or to reject nonconforming goods within an agreed period after delivery.
Then read the first few certificates against the shipment. Check the lot numbers against the carton marks, the drawing revision against your current release, and the report numbers against the reports you actually received. If they do not match, raise it on the first shipment, while the habit is still being formed.
Where Jack fits
JCH runs manufacturing programs at vetted partner factories. Our inspection step describes how orders are checked: the incoming material, the first article against your drawing, parts pulled while the line runs, and the lot before it ships against an agreed sampling plan. Those reports are what a certificate of conformance should point to, and Jack can set the CoC requirements in your purchase order up front so each shipment's certificate names its lot and its reports. JCH itself holds no certification. Where a buyer requires ISO, UL or a third-party test, Jack matches the program to partner facilities and accredited labs that hold them.
If you want a certificate of conformance that means something, send Jack your drawing and your PO terms and he will tell you what the factory can certify, what it should attach, and what you should still inspect yourself.
Straight answers
What is a certificate of conformance?
A certificate of conformance (CoC) is a signed statement from a supplier that a specific shipment or lot meets the purchase order, drawing and specifications. A useful one names the PO, part number, drawing revision, lot and quantity, the requirements it certifies to, and the inspection or test reports behind it.
Is a certificate of conformance the same as a certificate of compliance?
In everyday purchasing the terms are often used interchangeably. In regulated settings they are not: for US consumer products, the CPSC requires a certificate of compliance (a General Certificate of Conformity or a Children's Product Certificate) issued by the importer or domestic manufacturer, and a factory's own CoC does not replace it.
Does a certificate of conformance replace inspection?
No. It is the supplier's own statement, not independent evidence. Buyers usually verify new parts with a first article inspection and early lots with a pre-shipment inspection, and only reduce inspection once the supplier has a good record. The purchase order should keep the right to inspect and reject.
Who issues the CPSC certificate for imported products?
Under 16 CFR part 1110, for finished products made outside the United States the importer is the finished product certifier and must issue the certificate. The importer can rely on other parties for testing or data entry but remains legally responsible for the certificate.
What should a purchase order say about certificates of conformance?
Require a CoC with each shipment that references the PO, part number, drawing revision, lot and quantity; list the reports it must attach or reference; require approved deviations to be listed; and state that accepting the CoC does not waive your right to inspect or reject nonconforming goods.
How this note was made: researched and drafted with AI assistance, checked against the sources listed below and edited at JCH Design & Manufacturing.