JCH Design & ManufacturingJCH Design & Manufacturing BBB Accredited BusinessBook a 30-min call
Last updated 2026-11-12  ·  By the JCH engineering team

Threaded inserts for plastic: molded-in, heat-set or press-in, and which to specify

A metal thread in a plastic part can be molded in or installed after molding by heat, ultrasonics or a press. Here is how the four compare, what the part design must get right, and the brief that gets an accurate quote.

Filed under Insert molding and overmolding

Short answer: Threaded inserts for plastic put a metal thread where a screw has to go in and out more than a few times, or hold a load the plastic thread cannot. There are four common ways to fit them: molded in by the factory during the shot, or installed after molding by heat, ultrasonic vibration or a press. Molded-in usually performs best but costs press time and risk at the mold; post-mold installation is cheaper and simpler but depends on getting the hole right. Decide which one before the tool is cut, because the hole, the boss and the mold all change with it.

A screw driven straight into plastic is fine for a battery door that opens twice a year. It is not fine for a housing that gets serviced, a bracket that carries a load, or a joint that must hold its clamp over years of temperature swings. That is where a brass or steel insert earns its cost. This note covers the four installation methods, what each one asks of the part design, and what to put in front of a factory so the quote and the tool match what you need. For the broader process, see our insert molding and overmolding page.

Why use a threaded insert at all

Wikipedia's article on threaded inserts notes that "Threaded inserts are commonly used in plastic casings, housing, and parts to create a metal thread", typically brass or stainless steel, so screws can be used to assemble consumer products and electronics. One insert maker, PennEngineering, says inserts are typically specified where strong metal threads are needed in plastic, "especially where frequent assembly and disassembly of the unit for service or repair is necessary".

The DuPont design guide for its engineering polymers sets a sensible bar: "Inserts should be used when there is a functional need for them and when the additional cost is justified by improved product performance." Its four reasons are threads that will see continuous stress or frequent disassembly, close tolerances on female threads, a permanent way to attach two highly loaded parts, and electrical conductance. If none of those apply, a well-designed boss and a thread-forming screw may be all you need, and it costs less.

The four ways to install an insert

Molded in. The insert is placed in the open mold before each shot, and the plastic forms around it. Wikipedia's injection molding article describes it that way and notes it is often used for plastic parts with metal screws that need to be fastened and unfastened repeatedly. PennEngineering explains how threaded inserts sit in the tool: they are located in the cavity on core pins, and "When the mold opens, the core pins are withdrawn leaving the inserts permanently encapsulated in the plastic section with only the threads exposed." "Installing the inserts during the molding process eliminates the need for secondary steps or installation equipment."

An open injection mold half on a wooden bench, showing the polished cavity, core pins, leader pin holes and a lifting eye
An open mold half at a partner factory. A molded-in insert has to sit on a pin or in a pocket cut into steel like this, in the same place on every shot.

Heat-set. A heated insert is pressed into a molded or drilled hole. The plastic around it softens, flows into the knurls and grooves, and locks the insert when it cools. SPIROL's design guide says its heat and ultrasonic inserts "are designed for post-mold installation in thermoplastics", so this route is for thermoplastics, not thermosets.

Ultrasonic. The same idea with vibration instead of a heated tip. From Wikipedia: "The ultrasonic vibrations melt the thermoplastic material where the metal insert is in contact, and pressure is applied to press it into position."

Press-in. The insert is pushed into a plain hole cold. PennEngineering notes that "Installation is accomplished using any standard press at any time during the production process." The trade-off is performance. SPIROL says its press-in inserts "These Inserts are designed to reduce installation cost at a sacrifice of torque and pull-out performance."

Molded-in or post-mold: the real trade-off

The two insert makers say much the same thing from opposite sides. SPIROL: "Molding the Inserts into the plastic assembly, although more costly than installing the Inserts after the molding process is completed, provides the best performance." Then the counterweight: "Installation of Inserts after molding reduces in-place cost by shortening molding time and eliminating secondary cleaning. This method also reduces rejects and mold damage resulting from dislodged Inserts."

The DuPont guide lists the practical problems with molding inserts in. Inserts can "float" or shift and damage the mold. "Inserts are often difficult to load, which can prolong the molding cycle." Inserts may need preheating. And "Inserts in rejected parts are costly to salvage." Every insert has to be loaded by hand or by robot on every cycle, so molded-in inserts add cycle time on every part you buy, not only on the first lot.

The bigger quality risk is cracking. In DuPont's words, "The most common complaint associated with insert molding is delayed cracking of the surrounding plastic because of molded-in hoop stress." The plastic shrinks onto the metal as it cools and stays in tension around it. The guide shows this matters far more in some resins than others, and that toughened grades with higher elongation resist it better. That is one more reason the resin choice and the insert choice belong in the same conversation; our note on injection molding materials covers how to pick a resin.

A rough rule we use with buyers: if the insert carries real load or torque, or the part is a thermoset, start from molded-in and price it. If the part is a thermoplastic housing that gets a few screws for assembly and service, heat-set or ultrasonic after molding is usually the better buy. Ask the factory to quote both when it is close.

What the part design has to get right

Most insert failures are designed in before the tool is cut. The insert makers' guides agree on a handful of points:

None of these numbers replaces the insert maker's sheet for the exact part number you buy. Put that part number on the drawing.

What to send a factory

A clear brief gets a quote you can hold the factory to, and a tool built for the insert you actually want. Send:

A partner factory test lab with benches of test fixtures and an environmental test chamber at the back of the room
A partner factory test lab. Torque-out, pull-out and temperature-cycle checks on first parts are where insert problems show up before production.
  1. The drawing, with every insert called out by maker and part number, thread size, and the installation method you want or are open to.
  2. The resin, including any glass or mineral fill, since filler changes the hole size and the cracking risk.
  3. The load case: how many times the screw goes in and out over the product's life, and the torque or pull-out the joint must hold.
  4. Who supplies the inserts. Name-brand inserts or the factory's local source; if local, ask for the insert's own drawing and material certificate.
  5. What you will test. DuPont advises a thorough end-use test program at the prototype stage, and that "Testing should include temperature cycling over the range of temperatures to which the application may be exposed." Add torque-out and pull-out checks on first articles; our note on first article inspection covers how to structure them.

Then check the first parts the hard way: drive the screw to torque, back it out, repeat to the count your product will see, and look for cracks around the boss after a temperature cycle. Most insert problems show up there, and they cost far more to find in the field.

Where Jack fits

JCH runs insert molding, overmolding and post-mold insert installation as part of a manufacturing program at vetted partner factories. Jack works the way our molding step describes: a DFM review before the tool is cut, sampled parts you approve, then production with first-article and in-line checks. Where your drawing calls for a specific insert brand, he sources that part; where it allows an equivalent, he shows you the drawing and certificate before it goes into the program. JCH itself holds no certification. Where a buyer requires ISO, UL or a third-party test, Jack matches the program to partner facilities and accredited labs that hold them.

If you have a part that needs a metal thread, send Jack the drawing and he will tell you which insert method fits and what to change before the tool is cut.

Straight answers

What are threaded inserts for plastic?

They are metal bushings, usually brass or stainless steel, with an internal thread. They are set into a plastic part so a screw can be driven in and out many times, or carry more load than a thread cut or formed directly in the plastic.

What is the difference between molded-in and heat-set inserts?

Molded-in inserts are placed in the mold before each shot, and the plastic forms around them. Heat-set inserts are pressed into a molded or drilled hole after molding while heated, so the softened plastic flows into the knurls and locks them in when it cools. Molded-in generally performs best; heat-set costs less press time and avoids mold damage from a dislodged insert.

Can heat-set or ultrasonic inserts be used in thermoset plastic?

No. Heat and ultrasonic installation work by melting thermoplastic around the insert. For thermosets, inserts are molded in or installed mechanically, for example press-in or self-tapping types; check the insert maker's guide for your resin.

Why does the plastic crack around a molded-in insert?

The plastic shrinks onto the metal as it cools and is left in tension around the insert, known as hoop stress. Sharp insert edges, a thin boss, a weak knit line and a resin with low elongation all raise the risk, and the cracking can appear long after molding.

What should I tell a factory when quoting a part with inserts?

Give the drawing with each insert's maker, part number and thread, the installation method you want, the resin and any filler, how often the screw will be removed and the load it must hold, who supplies the inserts, and the torque-out, pull-out and temperature-cycle checks you expect on first articles.

threaded inserts for plasticheat set insertsmolded-in insertsinsert moldingultrasonic insertionpress-in insertsboss designhoop stress

How this note was made: researched and drafted with AI assistance, checked against the sources listed below and edited at JCH Design & Manufacturing.

Have something you need made?

Bring an idea, a sketch, a sample or a finished product. Jack reads every inquiry himself.

Ask for time with Jack