JCH Design & ManufacturingJCH Design & Manufacturing BBB Accredited BusinessBook a 30-min call
Last updated 2026-11-10  ·  By the JCH engineering team

Overmolding vs insert molding: what is the difference, and which do you need?

Insert molding places a preformed part, usually metal such as a threaded nut, pin or contact, into the mold and shoots plastic around it in one shot. Overmolding molds a second material, usually a soft TPE or TPU, over a plastic part that was molded first.

Filed under Insert molding and overmolding

Short answer: Use insert molding when the part needs metal strength, threads or electrical contact locked into plastic. Use overmolding when the part needs a soft grip, seal or second color over a rigid body. Both rely on a good bond and a tool designed to hold the first part in place.

Insert molding and overmolding are often mentioned together, and some suppliers use the terms loosely. They solve different problems. Insert molding joins plastic to something that is not molded in that tool, usually metal. Overmolding joins two plastics, usually a soft one over a rigid one.

How each process works

Insert molding. A preformed insert is loaded into the open mold by hand or robot. The tool closes and plastic is injected around it, locking it in place. Xometry describes metal components positioned in the cavity, by hand or by robot, before the plastic goes in; one of the most common uses is metal threads for fasteners. It can replace a separate step of fitting inserts after molding.

Overmolding. A rigid substrate is molded first. It is then placed in a second tool, or moved within a two-shot tool, and a second material is molded over it. Pexco frames the difference simply: insert molding is typically plastic over a preformed insert, often metal, and overmolding is typically plastic over plastic. Xometry adds that overmolding needs either two tools or a more complex two-shot tool. Overmolding itself can be done with two tools or with one two-shot tool, which is covered in two-shot molding vs overmolding.

Insert molding vs overmolding at a glance

Insert moldingOvermolding
What goes in firstA preformed insert, usually metalA molded plastic substrate
What is addedPlastic around the insertA second plastic, often soft TPE or TPU
ShotsOneTwo: two tools, or one two-shot tool
Typical purposeThreads, strength, electrical contactGrip, seal, cushioning, second color
BondMostly mechanical: knurls, grooves, undercutsChemical plus mechanical; depends on matched grades
Main riskInsert position, insert movement, cracking around metalPeeling, flash at the shut-off line, warpage
Typical partsThreaded housings, connectors, knobs with metal shaftsTool and power tool grips, cases, seals

Design points for each

Insert molding

  • Lock the insert. Knurls, grooves or undercuts on the insert give the plastic something to grip, so the insert does not spin or pull out.
  • Hold it in the tool. The mold needs pins, pockets or magnets that hold the insert exactly in place while plastic flows around it.
  • Watch the plastic around metal. Plastic shrinks as it cools and metal does not, which can stress the plastic around the insert. Enough wall around the insert reduces cracking.

Overmolding

  • Match the materials. Soft grades are sold to bond to specific substrates such as PC, ABS, PP or nylon. Ask for the datasheet that names yours.
  • Add a mechanical lock where the bond matters: holes, grooves or undercuts the soft material can flow into.
  • Design a clean shut-off where the soft material stops, so the tool can seal against it without flash.

Formlabs notes that both processes can be prototyped before production tooling, which is a sensible way to test the bond or the insert hold first.

When to choose which

Choose insert molding when

  • The part needs metal threads that will be assembled many times.
  • It needs an electrical contact or pin locked into plastic.
  • A metal shaft or reinforcement has to be held firmly in a plastic body.

Choose overmolding when

  • The part needs a soft grip, seal or bumper over a rigid body.
  • A second color or texture has to be permanently joined.
  • You want to remove a separate assembly or glue step.

Some parts need both: a metal insert in a rigid body with a soft overmold on top. Jack's partner lines run inserts such as nuts and pins, overmolding and two-shot, described on the insert molding and overmolding page.

What to send for a quote

  1. CAD for the plastic part and the insert or soft layer.
  2. The insert spec, and whether you supply it or the supplier sources it.
  3. Materials and, for soft layers, hardness and color.
  4. What the bond or insert must survive: torque, pull-out, peel or heat.
  5. Annual volume.

Material choice is covered in how to choose a resin.

Straight answers

What is the difference between insert molding and overmolding?

Insert molding places a preformed part, usually metal, in the mold and molds plastic around it in one shot. Overmolding molds a second material, usually a soft one, over a plastic part that was molded first.

Is insert molding a type of overmolding?

Some suppliers describe it that way, because plastic is molded over another part. In practice the terms are used differently: insert molding for preformed inserts such as metal, overmolding for plastic over plastic.

What inserts can be insert molded?

Common inserts include threaded nuts, pins, shafts, electrical contacts and reinforcements. The insert needs features such as knurls or grooves so the plastic can lock onto it.

Will a soft overmold stay bonded?

Only with matched materials and good design. Choose a soft grade made to bond to your substrate, add a mechanical lock where the bond matters, and test pull or peel at first article.

Can one part use both processes?

Yes. A part can have a metal insert molded into a rigid body, then a soft layer overmolded on top.

insert moldingovermoldingmetal insertsthreaded insertsTPEsoft-touchtwo-shot

How this note was made: researched and drafted with AI assistance, checked against the sources listed below and edited at JCH Design & Manufacturing.

Have something you need made?

Bring an idea, a sketch, a sample or a finished product. Jack reads every inquiry himself.

Ask for time with Jack