Aluminum vs steel injection molds: aluminum, P20 and H13 compared
Aluminum molds cost less and are quicker to cut, but they wear faster; steel molds cost more and last far longer. Between the steels, P20 is the usual pre-hardened choice for moderate volumes, and H13 is the hardened choice for long runs and abrasive resins.
Filed under Molds and tooling
Short answer: Pick aluminum when volume is modest or uncertain and the design may still change. Pick P20 steel for steady medium volumes in ordinary resins, and hardened H13 for long programs, glass-filled resins or high-polish surfaces that have to hold up. The resin and the lifetime volume decide it more than the price of the steel.
The material a mold is cut from sets how long it lasts, how easily it can be changed, and what resins it can run. Buyers usually see the choice as a line on a quote: "aluminum," "P20," "H13," or a stainless grade. This note explains what those words commit you to, so the quote you accept matches the program you actually have.
The three families of mold material
Aluminum. Soft, quick to machine and very good at moving heat out of the part. Fictiv points out that aluminum tools are not always limited to short runs: with the right construction and conditions, some last much longer than buyers expect. They still wear faster than steel, especially at gates and fine features.
Pre-hardened steel (P20 and similar). Supplied already hardened to a moderate level, so it can be machined without a later heat-treat step. It is the common middle ground: far tougher than aluminum, easier to modify than fully hardened steel. Fictiv and Xcentric Mold both describe P20 as a moderate-volume steel.
Hardened steel (H13, stainless grades). Machined, then heat-treated to a high hardness. It resists wear and holds a polish over long runs, and it stands up to glass-filled and other abrasive resins. Stainless grades are chosen where the resin is corrosive or the surface must stay optically clean. Fictiv's tooling life guide lists H13 among the long-life production steels.
Aluminum vs P20 vs H13 at a glance
| Aluminum | P20 (pre-hardened steel) | H13 (hardened steel) | |
|---|---|---|---|
| Upfront tool cost | Lowest | Middle | Highest |
| Build speed | Fastest to machine | Moderate | Slowest: machining plus heat treatment |
| Wear resistance | Lowest; gates and edges wear first | Good for ordinary resins | Highest; suits abrasive, glass-filled resins |
| Design changes | Easiest to weld and re-cut | Workable | Hardest and costliest to change |
| Surface finish over time | Polish degrades sooner | Holds a standard finish | Holds a high polish longest |
| Typical fit | Prototypes, bridge runs, uncertain demand | Steady medium volumes | Long programs, high volumes, demanding resins |
What really decides it: resin and lifetime volume
General rules like "aluminum is cheap, steel lasts forever" skip the two inputs that matter most. The first is the resin. A glass-filled nylon erodes a soft tool's gates quickly, while an unfilled polypropylene is gentle on it. The second is lifetime volume: not this year's order, but how many parts the tool must make before the product is retired or redesigned.
That is why the right question for a supplier is not "aluminum or steel?" but "what tool life do you expect, in shots, for this resin and this geometry?" Ask for that number in writing and compare it with your own forecast. Mold wear also shows up before end of life: flash along the parting line is often the first sign, as Fictiv notes.
When to choose which
Choose aluminum when
- Demand is unproven and you want real molded parts in the production resin before committing to steel.
- The design is likely to change after the first customers handle it.
- The resin is unfilled and gentle on tooling.
- You need a bridge tool to ship while a steel tool is built.
Choose P20 when
- The design is stable and volumes are steady but not huge.
- The resin is a common commodity or engineering grade without heavy filler.
- You want room to make modest changes without re-cutting hardened steel.
Choose H13 or another hardened steel when
- The program is expected to run for a long time at high volume.
- The resin is glass-filled or otherwise abrasive.
- The part has a cosmetic, high-polish surface that has to stay consistent lot after lot.
Many tools mix materials: a P20 mold base with hardened inserts at the gate or at features that wear. That is a normal way to put hard steel only where it earns its cost.
Questions to ask before steel is cut
- Which steel, or which aluminum grade, for the cavity, the core and any inserts?
- What tool life do you expect for my resin, in shots?
- Which features will wear first, and can they be inserted so they can be replaced?
- Who owns the tool, and is that stated on the quote? Our note on tooling custody covers what that clause should say.
- What does a design change cost on this material, roughly, compared with the original cut?
How material choice shows up in the total price is covered in what an injection mold really costs, and how a tool is cut and proved is in mold making: how an injection mold is built. Jack's position on cost is the same for every tool: the number depends on the detail of the part, and he will not put a figure on it before he has seen it.
Straight answers
Is an aluminum mold good enough for production?
It can be, when volume is modest, the resin is gentle and the design is settled. Aluminum wears faster than steel, so ask the supplier for an expected tool life in shots for your resin and compare it with your lifetime forecast.
What is the difference between P20 and H13 steel?
P20 is a pre-hardened steel that is machined as supplied and suits moderate volumes. H13 is machined and then heat-treated to a much higher hardness, which makes it more wear-resistant for long runs and abrasive resins, and harder to modify.
Does a steel mold always cost more than an aluminum mold?
Upfront, usually yes, because steel machines more slowly and hardened steel needs heat treatment. Over a long program the steel tool can cost less per part because it does not need to be replaced or repaired as often.
Can a mold mix aluminum and steel?
Yes. Hybrid tools are common, for example a softer mold base with hardened steel inserts at gates or at features that wear. This puts hard steel only where it is needed.
What should I ask a supplier about mold material?
Ask which material is used for the cavity, core and inserts, the expected tool life in shots for your resin, which features wear first, what a design change would involve, and who owns the finished tool.
How this note was made: researched and drafted with AI assistance, checked against the sources listed below and edited at JCH Design & Manufacturing.