Hot runner vs cold runner: which does your mold need?
A cold runner lets the plastic channels freeze with the part each shot, so the tool is simpler and cheaper but leaves a runner to trim or regrind. A hot runner keeps those channels molten, so there is no runner scrap and cycles are usually faster, at a higher tool cost and more upkeep.
Filed under Molds and tooling
Short answer: Choose a cold runner for low to medium volumes, frequent color changes, heat-sensitive resins and tight tooling budgets. Choose a hot runner when volume is high, the resin is expensive or cannot be reground, there are many cavities, or the gate has to be nearly invisible. Model the whole cost, including maintenance, not just the resin saved.
What is the difference between a hot runner and a cold runner?
A cold runner's channels are unheated, so the plastic in them freezes with the part and is trimmed or reground every shot. A hot runner keeps those channels molten with a heated manifold and nozzles, so only the part is ejected. That means less runner scrap and often a faster cycle, but a costlier tool and more upkeep.
Every injection mold needs a path from the machine nozzle to the cavities. That path is the runner, and whether it is heated or not changes the tool price, the scrap rate, the cycle and the look of the part. Quotes often state "hot runner" or "cold runner" without explaining the trade, so this note lays it out.
How each system works
Cold runner. The channels are cut into the mold plates and are not heated. Each shot, the plastic in them cools along with the part and is ejected as a runner, which is cut off and either scrapped or ground up and reused as regrind if the material and spec allow.
Hot runner. A heated manifold and nozzles keep the plastic molten up to the gate. Only the part cools and ejects. Carmo summarizes the trade: no runner to trim and usually a faster cycle, in exchange for costlier tooling, more maintenance and slower color changes. Hot runners also allow valve gates, which open and close on command and leave a very small gate mark.
Hot runner vs cold runner at a glance
| Cold runner | Hot runner | |
|---|---|---|
| Tool cost | Lower; no manifold or controls | Higher; manifold, heaters, nozzles, controller |
| Runner scrap | A runner every shot, trimmed or reground | None at the part |
| Cycle | Runner must cool, which can lengthen the cycle | Usually shorter |
| Gate mark | Trimmed gate vestige | Small vestige; valve gates can be near flush |
| Color and material changes | Quick; the runner leaves with every shot | Slower; the manifold must be purged |
| Heat-sensitive resins | More forgiving | Needs care; resin sits hot in the manifold |
| Maintenance | Simple; channels are visible and easy to change | Heaters, thermocouples and tips need upkeep |
| Typical fit | Prototype to medium volume, varied runs | High volume, many cavities, costly resin |
The savings on paper are not always real
MoldMaking Technology makes the point plainly: a hot runner uses less material, but leaks, downtime and control problems can create scrap of their own, and "the savings on paper do not always add up to real money in the bank." The same article lists cold runner advantages that buyers rarely hear: gate locations are easy to change, the channels can be measured directly, and there are no heaters or thermocouples to drift.
Treat a hot runner as an investment. Count the direct cost of the system and its spares, and the indirect cost of purging, training and repair downtime, and set it against the resin and cycle saved over the expected life of the program. NICE Rapid notes that on low to mid volume programs the extra tooling cost may never be recovered.
When to choose which
Choose a cold runner when
- Volume is low to medium, or demand is still uncertain.
- You run many colors or change materials often.
- The resin is heat-sensitive.
- The runner can be reground and reused under your spec.
- A trimmed gate mark is acceptable on a non-cosmetic face.
Choose a hot runner when
- Volume is high and steady, so faster cycles and zero runner scrap add up.
- The resin is expensive, or regrind is not allowed for the part.
- The tool has many cavities that must fill evenly.
- The gate sits on a visible surface and must be near invisible.
There are hybrids too: a hot drop feeding a short cold sub-runner, for example. Ask the toolmaker why they chose the system on your quote; a clear answer is a good sign.
What to settle on the quote
- Runner type, and for a hot runner, the gate type (open tip or valve gate) and who supplies the controller.
- Gate locations, marked on the part drawing, with cosmetic faces identified.
- Whether regrind is allowed, and at what share, under your spec.
- Spare heaters, tips and thermocouples: included or not.
- Ownership of the tool, including the hot runner system, stated in writing.
Runner choice is one of the reasons two quotes for the same part can look so different; see why injection mold quotes vary. Gate and runner problems also show up as defects, covered in injection molding defects: tool or process? The words you will see on the quote are defined in injection molding terminology.
Straight answers
What is the difference between a hot runner and a cold runner?
A cold runner's channels are unheated, so the plastic in them solidifies with the part and is ejected and trimmed each shot. A hot runner keeps the channels molten with a heated manifold and nozzles, so only the part is ejected.
Is a hot runner always better?
No. It costs more to build and maintain, slows color changes and needs care with heat-sensitive resins. At low to medium volumes a cold runner often costs less overall.
Does a hot runner reduce part cost?
It can, by removing runner scrap and shortening the cycle. Whether it lowers total cost depends on volume, resin price, regrind rules and maintenance over the life of the program.
What is a valve gate?
A valve gate is a hot runner nozzle with a pin that opens and closes the gate on command. It gives control over filling and leaves a small, often near-flush gate mark.
Can cold runner scrap be reused?
Often, as regrind mixed with new resin, if the material and the part specification allow it. Some regulated or high-performance parts do not allow regrind, which makes the runner true scrap.
How this note was made: researched and drafted with AI assistance, checked against the sources listed below and edited at JCH Design & Manufacturing.