SPI mold classes explained: what Class 101 to 105 tells you about a tool
The SPI mold classes are an industry shorthand, from Class 101 to Class 105, for how many cycles a mold is built to run and how robustly it is built. Class 101 is the most durable, built for very high volume; Class 105 is a prototype tool for a handful of parts.
Filed under Molds and tooling
Short answer: Use the SPI class to make sure two quotes describe the same kind of tool. Ask for the class in writing, then check the details behind it: steel, hardness, cooling, wear plates and documentation. The class describes how the tool is built; it does not tell you how long it will last on your part.
Mold quotes often carry a line such as "SPI Class 102." The classification comes from the plastics industry trade association once known as SPI, the Society of the Plastics Industry, now called the Plastics Industry Association. It gives buyers and toolmakers a common vocabulary for how robust a tool is. It is useful exactly because two quotes that look alike can describe very different tools.
The five classes
Published summaries, such as the table in Fictiv's tooling life guide, describe the classes by expected volume. These are industry descriptions of each class, not a figure for any particular part.
| Class | Volume described | Cycles described | Typical build | Typical use |
|---|---|---|---|---|
| 101 | Very high | One million or more | Hardened steel throughout, full cooling, wear plates, documented | Long-running, high-volume parts |
| 102 | Medium to high | Up to about one million | Hardened molding surfaces, robust base | Steady production, including abrasive resins |
| 103 | Medium | Under about half a million | Pre-hardened steel is common | Typical medium-volume production |
| 104 | Low | Under about one hundred thousand | Mild steel or aluminum | Limited production, non-abrasive resins |
| 105 | Prototype | A few hundred or fewer | Cast metal, aluminum or other quick materials | Prototype parts only |
What the class does and does not tell you
The class describes the build: what steel is used where, how hard the molding surfaces are, how the tool is cooled, and whether it has features such as wear plates and guided ejection. Higher classes cost more because they use harder steel, more machining and more documentation.
The class does not tell you how many good parts your specific tool will make. Tool life depends on the resin, the part geometry, the press, the process and the maintenance. A glass-filled resin wears any tool faster than an unfilled one. Fictiv notes that molds with moving mechanisms or hand-loaded inserts tend to have shorter lives, and that poor temperature control, excessive clamp force or misalignment shorten life further.
When to choose which class
- Class 101 or 102 when the part will run at high volume for a long time, the resin is abrasive, or downtime is very costly.
- Class 103 for steady medium-volume production of a stable design.
- Class 104 for limited runs or bridge production in gentle resins.
- Class 105 only to prove a design with a small number of real molded parts.
Buying a higher class than the program needs ties up money in steel that will never be used. Buying a lower class than the program needs means repairs, downtime and a second tool. The honest starting point is your lifetime volume forecast and the resin. Material choices behind the classes are compared in aluminum vs steel injection molds.
How to use the class on a quote
- Ask every supplier to state the SPI class, or the equivalent build description, in writing.
- Ask for the steel and hardness for the cavity, core and inserts, not just the class number.
- Ask what tool life they expect for your resin, in shots.
- Ask what maintenance the tool needs and who does it.
- Confirm who owns the tool. See tooling custody.
Class is one reason two quotes for the same part can differ so much; see why injection mold quotes vary and what an injection mold really costs. Other quote terms are defined in injection molding terminology.
Straight answers
What are SPI mold classes?
They are an industry classification, Class 101 to Class 105, describing how robustly an injection mold is built and the volume it is built for, from very high volume (101) to prototype (105).
What is an SPI Class 101 mold?
The most durable class, described for one million or more cycles, typically with hardened steel, full cooling, wear plates and full documentation. It is meant for long-running, high-volume parts.
Does the SPI class tell me how long my mold will last?
Not exactly. It describes the build. Actual life depends on resin, part geometry, process, press and maintenance, so ask the supplier for an expected tool life for your resin.
Which SPI class do I need?
Match the class to your lifetime volume and resin. High volume or abrasive resins point to 101 or 102; steady medium volume to 103; limited runs to 104; prototypes to 105.
Who created the SPI mold classes?
The plastics industry trade association formerly known as SPI, the Society of the Plastics Industry, now the Plastics Industry Association.
How this note was made: researched and drafted with AI assistance, checked against the sources listed below and edited at JCH Design & Manufacturing.